LTE实训报告.doc

成 绩 重庆邮电大学通信与信息工程学院移动通信综合实训报告专 业 班 级 学 号 姓 名 实验时间： 重庆邮电大学通信与信息工程学院通信技术与网络实验中心制一、实验题目LTE无线侧综合实验二、实验目的1.熟悉LTE网络结构2.了解和学习华为eNodeB设备DBS3900系统功能3.掌握华为TDD-LTE的eNodeB数据配置方法4.获得通信网络工程的实际应用技能三、实验内容数据脚本：MOD ENODEB: ENODEBID=101, NAME=cytx, ENBTYPE=DBS3900_LTE, LOCATION=cyyfl, PROTOCOL=CPRI;LST ENODEB:;ADD CNOPERATOR: CnOperatorId=1, CnOperatorName=cytx, CnOperatorType=CNOPERATOR_PRIMARY, Mcc=460, Mnc=02;ADD CNOPERATORTA: TrackingAreaId=1, CnOperatorId=1, Tac=100;ADD BRD: CN=0, SRN=0, SN=6, BT=UMPT;ADD BRD: CN=0, SRN=0, SN=18, BT=UPEU;ADD BRD: CN=0, SRN=0, SN=19, BT=UPEU;ADD BRD: CN=0, SRN=0, SN=2, BT=LBBP, WM=TDD;ADD BRD: CN=0, SRN=0, SN=16, BT=FAN;DSP BRD:;ADD RRUCHAIN: RCN=0, TT=CHAIN, AT=LOCALPORT, HCN=0, HSRN=0, HSN=2, HPN=0, CR=9.8;ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RN=xinke, ALMPROCSW=ON, ALMPROCTHRHLD=30, ALMTHRHLD=20, RS=TDL, RXNUM=1, TXNUM=1;ADD GPS: GN=0, CN=0, SRN=0, SN=6, CABLETYPE=COAXIAL, CABLE_LEN=20, MODE=GPS, PRI=4;SET CLKMODE: MODE=AUTO;SET CLKSYNCMODE: CLKSYNCMODE=TIME;ADD ETHPORT: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PN=0, PA=COPPER, MTU=1500, SPEED=100M, ARPPROXY=DISABLE, FC=CLOSE, FERAT=10, FERDT=8, DUPLEX=FULL;ADD DEVIP: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, IP=110.110.110.3, MASK=255.255.255.0;ADD IPRT: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, DSTIP=134.134.134.10, DSTMASK=255.255.255.0, RTTYPE=NEXTHOP, NEXTHOP=110.110.110.1, PREF=60, DESCRI=TO MME;ADD IPRT: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, DSTIP=135.135.135.10, DSTMASK=255.255.255.0, RTTYPE=NEXTHOP, NEXTHOP=110.110.110.1, PREF=60, DESCRI=TO SGW;ADD IPRT: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, DSTIP=172.100.100.16, DSTMASK=255.255.255.0, RTTYPE=NEXTHOP, NEXTHOP=110.110.110.1, PREF=60, DESCRI=TO OMC;LST IPRT:;ADD S1SIGIP: CN=0, SRN=0, SN=6, S1SIGIPID=TO MME, LOCIP=110.110.110.3, LOCIPSECFLAG=DISABLE, SECLOCIP=0.0.0.0, SECLOCIPSECFLAG=DISABLE, LOCPORT=3000, RTOMIN=1000, RTOMAX=3000, RTOINIT=1000, RTOALPHA=12, RTOBETA=25, HBINTER=5000, MAXASSOCRETR=10, MAXPATHRETR=5, CHKSUMTX=DISABLE, CHKSUMRX=DISABLE, CHKSUMTYPE=CRC32, SWITCHBACKFLAG=ENABLE, SWITCHBACKHBNUM=10, TSACK=200, CNOPERATORID=1;ADD MME: MMEID=0, FIRSTSIGIP=134.134.134.10, FIRSTIPSECFLAG=DISABLE, SECSIGIP=0.0.0.0, SECIPSECFLAG=DISABLE, LOCPORT=3000, CNOPERATORID=1, MMERELEASE=Release_R8;ADD S1SERVIP: CN=0, SRN=0, SN=6, S1SERVIPID=TO SGW, S1SERVIP=110.110.110.3, IPSECFLAG=DISABLE, PATHCHK=DISABLE, CNOPERATORID=1;ADD SGW: SGWID=0, SERVIP1=135.135.135.10, SERVIP1IPSECFLAG=DISABLE, SERVIP2=0.0.0.0, SERVIP2IPSECFLAG=DISABLE, SERVIP3=0.0.0.0, SERVIP3IPSECFLAG=DISABLE, SERVIP4=0.0.0.0, SERVIP4IPSECFLAG=DISABLE, CNOPERATORID=1;ADD OMCH: FLAG=MASTER, IP=110.110.110.3, MASK=255.255.255.0, PEERIP=172.100.100.16, PEERMASK=255.255.255.0, BEAR=IPV4, CN=0, SRN=0, SN=6, SBT=BASE_BOARD, BRT=NO;ADD VLANMAP: NEXTHOPIP=110.110.110.1, MASK=255.255.255.0, VLANMODE=SINGLEVLAN, VLANID=100, SETPRIO=DISABLE;ADD SECTOR: SECN=0, GCDF=DEG, LONGITUDE=0, LATITUDE=0, SECM=NormalMIMO, ANTM=1T1R, COMBM=COMBTYPE_SINGLE_RRU, SECTORNAME=SHANQU, ALTITUDE=25, UNCERTSEMIMAJOR=3, UNCERTSEMIMINOR=3, ORIENTOFMAJORAXIS=0, UNCERTALTITUDE=3, CONFIDENCE=0, OMNIFLAG=FALSE, CN1=0, SRN1=60, SN1=0, PN1=R0A;ADD CELL: LocalCellId=0, CellName=CYTX, SectorId=0, CsgInd=BOOLEAN_FALSE, UlCyclicPrefix=NORMAL_CP, DlCyclicPrefix=NORMAL_CP, FreqBand=39, UlEarfcnCfgInd=NOT_CFG, DlEarfcn=38250, UlBandWidth=CELL_BW_N100, DlBandWidth=CELL_BW_N100, CellId=0, PhyCellId=99, AdditionalSpectrumEmission=1, FddTddInd=CELL_TDD, SubframeAssignment=SA2, SpecialSubframePatterns=SSP5, CellSpecificOffset=dB0, QoffsetFreq=dB0, RootSequenceIdx=1, HighSpeedFlag=LOW_SPEED, PreambleFmt=0, CellRadius=10000, CustomizedBandWidthCfgInd=NOT_CFG, EmergencyAreaIdCfgInd=NOT_CFG, UePowerMaxCfgInd=NOT_CFG, MultiRruCellFlag=BOOLEAN_FALSE, CPRICompression=NO_COMPRESSION;ADD CELLOP: LocalCellId=0, TrackingAreaId=1, CellReservedForOp=CELL_NOT_RESERVED_FOR_OP, OpUlRbUsedRatio=25, OpDlRbUsedRatio=25;ACT CELL: LocalCellId=0;第二次数据：数据脚本：MOD ENODEB: ENODEBID=101, NAME=CYTX, ENBTYPE=DBS3900_LTE, LOCATION=CYYFL, PROTOCOL=CPRI;LST ENODEB:;ADD CNOPERATOR: CnOperatorId=1, CnOperatorName=CYTX, CnOperatorType=CNOPERATOR_PRIMARY, Mcc=460, Mnc=04;DD CNOPERATORTA: TrackingAreaId=0, CnOperatorId=1, Tac=123;ADD BRD: CN=0, SRN=0, SN=6, BT=UMPT;ADD BRD: CN=0, SRN=0, SN=2, BT=LBBP, WM=TDD;ADD BRD: CN=0, SRN=0, SN=16, BT=FAN;ADD BRD: CN=0, SRN=0, SN=18, BT=UPEU;ADD BRD: CN=0, SRN=0, SN=19, BT=UPEU;ADD RRUCHAIN: RCN=0, TT=CHAIN, AT=LOCALPORT, HCN=0, HSRN=0, HSN=2, HPN=0, CR=9.8;ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RN=YFRRU, ALMPROCSW=ON, ALMPROCTHRHLD=30, ALMTHRHLD=20, RS=TDL, RXNUM=8, TXNUM=8;ADD GPS: GN=0, CN=0, SRN=0, SN=6, CABLETYPE=COAXIAL, CABLE_LEN=20, MODE=GPS, PRI=4;SET CLKMODE: MODE=AUTO;SET CLKSYNCMODE: CLKSYNCMODE=TIME;ADD ETHPORT: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PN=1, PA=FIBER, MTU=1500, SPEED=100M, ARPPROXY=DISABLE, FC=CLOSE, FERAT=10, FERDT=8, DUPLEX=FULL;ADD DEVIP: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=1, IP=110.110.110.3, MASK=255.255.255.0;ADD IPRT: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, DSTIP=134.134.134.10, DSTMASK=255.255.255.0, RTTYPE=NEXTHOP, NEXTHOP=110.110.110.1, PREF=60, DESCRI=TO MME;ADD IPRT: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, DSTIP=135.135.135.10, DSTMASK=255.255.255.0, RTTYPE=NEXTHOP, NEXTHOP=110.110.110.1, PREF=60, DESCRI=TO SGW;ADD IPRT: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, DSTIP=172.100.100.16, DSTMASK=255.255.255.0, RTTYPE=NEXTHOP, NEXTHOP=110.110.110.1, PREF=60, DESCRI=TO OMC;ADD S1SIGIP: CN=0, SRN=0, SN=6, S1SIGIPID=TO MME, LOCIP=110.110.110.3, LOCIPSECFLAG=DISABLE, SECLOCIP=0.0.0.0, SECLOCIPSECFLAG=DISABLE, LOCPORT=2900, RTOMIN=1000, RTOMAX=3000, RTOINIT=1000, RTOALPHA=12, RTOBETA=25, HBINTER=5000, MAXASSOCRETR=10, MAXPATHRETR=5, CHKSUMTX=DISABLE, CHKSUMRX=DISABLE, CHKSUMTYPE=CRC32, SWITCHBACKFLAG=ENABLE, SWITCHBACKHBNUM=10, TSACK=200, CNOPERATORID=1;ADD MME: MMEID=0, FIRSTSIGIP=134.134.134.10, FIRSTIPSECFLAG=DISABLE, SECSIGIP=0.0.0.0, SECIPSECFLAG=DISABLE, LOCPORT=2900, CNOPERATORID=1, MMERELEASE=Release_R8;ADD S1SERVIP: CN=0, SRN=0, SN=6, S1SERVIPID=TO SGW, S1SERVIP=110.110.110.3, IPSECFLAG=DISABLE, PATHCHK=DISABLE, CNOPERATORID=1;ADD SGW: SGWID=0, SERVIP1=135.135.135.10, SERVIP1IPSECFLAG=DISABLE, SERVIP2=0.0.0.0, SERVIP2IPSECFLAG=DISABLE, SERVIP3=0.0.0.0, SERVIP3IPSECFLAG=DISABLE, SERVIP4=0.0.0.0, SERVIP4IPSECFLAG=DISABLE, CNOPERATORID=1;ADD OMCH: FLAG=MASTER, IP=110.110.110.3, MASK=255.255.255.0, PEERIP=172.100.100.16, PEERMASK=255.255.255.0, BEAR=IPV4, CN=0, SRN=0, SN=6, SBT=BASE_BOARD, BRT=NO;ADD VLANMAP: NEXTHOPIP=110.110.110.1, MASK=255.255.255.0, VLANMODE=SINGLEVLAN, VLANID=100, SETPRIO=DISABLE;MOD VLANMAP: NEXTHOPIP=110.110.110.1, MASK=255.255.255.0, VLANMODE=SINGLEVLAN, VLANID=1011, SETPRIO=DISABLE;ADD SECTOR: SECN=0, GCDF=DEG, LONGITUDE=0, LATITUDE=0, SECM=NormalMIMO, ANTM=8T8R, COMBM=COMBTYPE_SINGLE_RRU, SECTORNAME=SEC1, ALTITUDE=25, UNCERTSEMIMAJOR=3, UNCERTSEMIMINOR=3, ORIENTOFMAJORAXIS=0, UNCERTALTITUDE=3, CONFIDENCE=0, OMNIFLAG=FALSE, CN1=0, SRN1=60, SN1=0, PN1=R0A, CN2=0, SRN2=60, SN2=0, PN2=R0B, CN3=0, SRN3=60, SN3=0, PN3=R0C, CN4=0, SRN4=60, SN4=0, PN4=R0D, CN5=0, SRN5=60, SN5=0, PN5=R0E, CN6=0, SRN6=60, SN6=0, PN6=R0F, CN7=0, SRN7=60, SN7=0, PN7=R0G, CN8=0, SRN8=60, SN8=0, PN8=R0H;ADD CELL: LocalCellId=0, CellName=CYTX_TEST_01, SectorId=0, CsgInd=BOOLEAN_FALSE, UlCyclicPrefix=NORMAL_CP, DlCyclicPrefix=NORMAL_CP, FreqBand=39, UlEarfcnCfgInd=NOT_CFG, DlEarfcn=38350, UlBandWidth=CELL_BW_N100, DlBandWidth=CELL_BW_N100, CellId=0, PhyCellId=112, AdditionalSpectrumEmission=1, FddTddInd=CELL_TDD, SubframeAssignment=SA0, SpecialSubframePatterns=SSP5, CellSpecificOffset=dB0, QoffsetFreq=dB0, RootSequenceIdx=156, HighSpeedFlag=LOW_SPEED, PreambleFmt=0, CellRadius=10000, CustomizedBandWidthCfgInd=NOT_CFG, EmergencyAreaIdCfgInd=NOT_CFG, UePowerMaxCfgInd=NOT_CFG, MultiRruCellFlag=BOOLEAN_FALSE, CPRICompression=NO_COMPRESSION;ADD CELLOP: LocalCellId=0, TrackingAreaId=0, CellReservedForOp=CELL_NOT_RESERVED_FOR_OP, OpUlRbUsedRatio=25, OpDlRbUsedRatio=25;ACT CELL: LocalCellId=0;四、故障处理及分析 1、首先要了解清楚各单板的功能及其接口，注意是电接口还是光接口，这些要从所给实训数据表中分析清楚，另外在单板中添加IP地址和子网掩码也要注意是在电接口端口还是光接口端口，而且在光接口时GE2的IP地址也要配置，第一次实验问题就出在这儿，还好最后我终于发现了。此外，在处理连线的时候也要选对线接口。2、通道以及端口号要正确配置。3.注意在画好图表以后一定要先保存，注意导入数据时要把数据初始化。五、实习收获与体会首先，接触到比较新的LTE的平台我非常高兴。通过本次学习我知道了LTE指的是无线侧的网络改进，更深入地了解了LTE的网络结构以及各个网元的功能。通过本次实训了解了LTE基站开通的注意事项，真实地了解了TDD-LTE以及FDD-LTE基站的区别。在实验过程中的一些操作以及注意事项，如要熟悉一些基本的网络架构及一些单板，其次就是绘制拓扑图一定要按脚本文件选择合适的设备，另外绘制好之后要先保存，连线和接口也要选对，这些都是配置前的准备，最后在配置的过程中要先配置传输数据，然后是基本数据无线数据，在实际操作中也一定要记得按实际设备来补充脚本，以便正确的导入到拓扑图等，对以后的工作实践有很大帮助。而且，通过测试中我们所犯的错误中我深刻体会到，值实际工程中，我们的数据配置一定得与设备相结合。总之，本次实训我收获很大，也感到非常兴奋，这次实训将为我以后的工作和深入学习打下坚实基础。