模具中英文对照

精选优质文档-倾情为你奉上1. 目的：为统一本厂冲压模具专业术语的中英文对照作业而制订本文件。2. 范围：适用于本公司各部门之作业。3. 职责：各部人员根据本节内容来进行相关作业。4. 内容：4.1.1 模具相关术语对照表：spotting spt 合模种类中文名称英文名称中文名称英文名称模具种类连续模Progressive die 冲孔模Pierce die机械手Transfer die剪边模Trimming die手动机械手Hand transfer die下料模Blanking die单工程模Single die成形模Forming die铸造结构模Cast die折弯模Bending die简易模Prototype die围边模Flange die铆合模Riveting die 拉伸模Draw die复合模Compound die快换模Changeable die工序类料带 strip料带图strip layout工序process冲导正孔pilot pierce冲孔pierce侧冲cam pierce切边notch切侧刃 notch french 折弯 bend墩薄 coin成形 form侧成形 cam form整形 restrike围边 flange打凸米 boss / dimple打凸包 emboss打字印 stamp打沙拉孔 hourglass面押 coin burr抽孔 extrude hole拍平 flat卷圆 curl种类中文名称英文名称中文名称英文名称工序类旋转rotate铆接 rivet产品切边线 trim line铆螺母 stake nut切断 cutoff接刀口 mismatch料带带料处 carrier tab毛刺方向 burr direction压线groove 下料blanking模板类上托板top plate下托板bottom plate上垫脚upper parallel下垫脚lower parallel上模座upper die set下模座lower die set上垫板punch backup 下垫板lower backup上夹板punch holder下夹板die holder上脱料板stripper下模板die plate 冲头punch凹模die零件类浮块 lifter浮料板 lifter plate 成型公 form punch压料块 pressure pad切边冲头 trim punch刀口 trim steel沉头孔 counter bore冲孔入子 button顶针 kick off / ejector废料切断刀 slug breaker成型凹模forming die整形公 restrike punch 导尺 rail 导尺顶杆 lifter bolt导料板 rail plate镶件/入子 insert侧冲组件 cam滑块 slide滑块上油槽 oil groove铲机 driver码模槽 mounting slot储运块 storage block限位柱stop block起吊孔 handing hole起吊环 eyebolt靠块 heel脱料板拉杆 spool模座导正块 thrust heel中文名称英文名称中文名称英文名称种类零件类耐磨片 wear plate垫片 shim压块keeper初始管位 first start pin键槽 key slot键 key氮气弹簧 nitrogen spring螺旋弹簧 coil spring聚氨酯弹簧 urethane 导柱 guide post导套 guide bushing插针 pilot pin插针套 pilot bushing侧刃 french传感器 sensor销 dowel螺丝 screw拔牙 jackscrew垫圈 washer盲销 blind dowel压毛边冲头deburring punch挡块stopping plate压线冲头groove punch定位块location block字模冲头stamp punch圆冲头round punch压筋冲头ribbon punch气垫板air cushion plate异形冲头special shape punch气垫顶杆air-cushion eject-rod切边冲头trimming punch上压块pressure block加强筋冲头stiffening rib punch弹簧箱spring box定位板guide plate弹簧箱顶杆spring-box eject-rod压边圈binder弹簧箱顶板spring-box eject-plate公差类公差 tolerance公差范围 tolerance range上公差 upper tolerance 下公差 lower tolerance公差+/- 0.05 plus minus 0.05形位公差图 GD&T平面度 flatness直线度 straightness倾斜度 angularity垂直度 perpendicularity平行度 parallelism圆度 roundness种类中文名称英文名称中文名称英文名称公差类圆柱度 cylindricity面轮廓度 surface profile线轮廓度line profile 位置度 true position同轴度 concentricity对称度 symmetry圆跳动 runout全跳动total runout尺寸 dimension角度值 angle degree尺寸全检报告dimensional layout三次元尺寸报告CMM report冲床相关机械冲床 mechanical press油压机 hydraulic press吨位 tonnage行程 stroke / travel冲床上台面 ram冲床下台面 bolster冲床台面布置图 press layout冲床上的快速对正 QDC冲床气垫 air cushion码仔 stirrup闭合高度 shut heightT型槽T-slot送料机 feeder送料高度 feeding height工具卡尺 caliper千分尺micrometer直尺ruler高度尺height gage丝攻 screw tap起子 screwdriver拨牙器 jacker扳手 wrench风磨机hand grinder油石oil stone加工类开料cutting material钻drill (DR)攻牙 tap铰 ream铣 mill车 lathe电脑锣 NC mill线切割 wire cutting(W/C)磨 grind刨 planer电火花 EDM镭射laser cutting倒角 chamferxx的精加工 finish XX真空热处理 vacuum heat treatment 镀钛 TD coating退磁 demagnetization 烧焊 weld 4.1.2 加工说明对照表：加工说明Machining Note注:有0.00的地方为数据填入处X:-0.00（氮气弹弓过孔，锣穿）单+0.00X:-0.00 (DR.THRU FOR GAS SPRING) S+0.00 X:-0.00（氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)X:-0.00 ( CNC CBORE TOP SIDE FOR GAS SPRING, S+0.00, DP0.00) X:-0.00（氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)X:-0.00 (CNC CBORE OPP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-0.00（合销孔,铰)X:-0.00 (REAM FOR DOWEL) X:-0.00（合销孔,割)单+0.00X:-0.00 (W/C FOR DOWEL) S+0.00 (正面沉头0.00*0.00深,内攻M0.00*1.5牙) (0.00*0.00 CBORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR) (反面沉头0.00*0.00深,内攻M0.00*1.5牙) (0.00*0.00 CBORE DP.0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-0.00（合销孔,钻穿)X:-0.00 (DR.THRU FOR DOWEL)X:-0.00（一般孔,钻穿)X:-0.00 (DR.THRU HL)X:-0.00（穿丝孔,钻穿)X:-0.00 (DR.THRU FOR WEDM S.H.)X:-0.00（漏油孔,钻穿)X:-0.00 (DR.THRU FOR DRAIN HL)X:-（漏油槽,反面CNC单+0.00,锣深0.00)X:- (CNC POCKET OPP.SIDE FOR DRAIN, S+0.00, DP0.00)X:-0.00（基准孔,铰)X:-0.00 (REAM FOR DATUM HL)X:-0.00钻穿（螺丝过孔)内攻M0.00牙X:-0.00 (DR.THRU FOR CLEARANCE HL, TAP M0.00 THR) (正面沉头0.00*0.00深) (0.00*0.00 CBORE DP0.00 TOP SIDE) (反面沉头0.00*0.00深) (0.00*0.00 CBORE DP0.00 OPP. SIDE) (侧面沉头0.00*0.00深) (0.00*0.00 CBORE DP0.00 EDGE SIDE)X:-M0.00钻穿,反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)X:-M0.00钻穿,正面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00钻穿,正反面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 OPP. SIDE, THR DP0.00)X:-M0.00盲孔,正面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00盲孔,正反面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,侧面分中攻深0.00,组模自配X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT) (侧面沉头0.00*0.00深) (0.00*0.00 CBORE DP0.00 EDGE SIDE)X:-M0.00盲孔,侧面分中钻深0.00X:-M0.00 BLIND HL, DR. DP0.00 ON EDGE FROM CENTERX:-M0.00钻穿（拨牙螺丝孔，攻穿）X:-M0.00 DR.THRU FOR JACK SCREW, TAP THRUX:-0.00（塞打过孔,钻穿)X:-0.00 DR.THRU FOR SPOOL X:-0.00（弹弓过孔,钻穿)X:-0.00 DR.THRU FOR SPRINGX:-0.00（弹弓孔,反面沉深0.00)有效深0.00X:-0.00 (CBORE FOR SPRING DP.0.00 OPP.SIDE, USED DP.0.00)X:-0.00（弹弓孔,正面沉深0.00)有效深0.00X:-0.00 (CBORE FOR SPRING DP.0.00 TOP.SIDE, WORK DP.0.00)X:-（避空孔,锣穿)单+0.00X:- (POCKET THRU)S+0.00X:-（避空孔,正面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE) X:-（避空孔,反面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)X:-0.00（避空孔,反面CNC单+0.00,锣深0.00)X:-0.00 (POCKET, CNC MILL S+0.00, DP0.00 OPP.SIDE) X:-0.00（避空孔,正面CNC单+0.00,锣深0.00)X:-0.00 (POCKET, CNC MILL S+0.00, DP0.00 EDGE SIDE)X:-0.00（两用销过孔,割)单+0.00X:-0.00 (LIFTER PIN, W/C S+0.00)X:-（导尺避空,CNC单+0.00锣穿)X:- (POCKET FOR RAIL, CNC MILL THRU, S+0.00)X:-（导尺避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 TOP SIDE, S+0.00)X:-（导尺避空,反面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 OPP. SIDE, S+0.00)X:-（浮块避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR LIFTER, CNC MILL DP.0.00 TOP SIDE, S+0.00)X:-（浮块孔,割）单+0.00 (反面避空单+0.00，锣深0.00)X:-（LIFTER HL, W/C)S+0.00 (POCKET DP0.00 S+0.00 OPP.SIDE)X:-（浮块孔,锣）单+0.00 (反面避空单+0.00，锣深0.00)X:-（LIFTER HL, MILL)S+0.00 (POCKET DP0.00 S+0.00 OPP.SIDE)X:-0.00（顶针孔,钻穿) （ 反面沉头0.00*0.00深，内攻M0.00*1.5牙)X:-0.00 (EJECT PIN, DR.THRU.) (0.00 CBORE DP0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-0.00（顶针孔,钻穿) （正面沉头0.00*0.00深，内攻M0.00*1.5牙)X:-0.00 (EJECT PIN, DR.THRU.) (0.00 CBORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)X:-0.00（导柱（导套）孔,CNC锣)单+0.00X:-0.00 CNC MILL FOR GUIDE PIN(BUSHING) S+0.00X:-0.00（导柱（导套）孔,割)单+0.00X:-0.00 W/C FOR GUIDE PIN(BUSHING) S+0.00 X:-M0.00*1.5(止付螺丝，正面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 TOP SIDE)X:-M0.00*1.5(止付螺丝，反面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 OPP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:-（INSERT HL, CNC MILL THRU S+0.00) (阴影部分正面沉头单+0.00，锣深0.00) (SHADE AREA, MILL DP0.00 S+0.00 TOP SIDE) (阴影部分反面沉头单+0.00，锣深0.00) (SHADE AREA, MILL DP0.00 S+0.00 OPP SIDE) X:-（入子孔,割）单+0.00X:-（INSERT HL, W/C S+0.00) (阴影部分扣位正面锣深0.00) (SHADE AREA FOR HEAD POCKET, MILL DP0.00 TOP SIDE) (阴影部分扣位反面锣深0.00) (SHADE AREA FOR HEAD POCKET, MILL DP0.00 OPP. SIDE) (正面沉头单+0.00，锣深0.00) (POCKET, MILL DP0.00 TOP SIDE) 注: 此处的沉头不能用CBORE, 只有圆形的沉头才用CBORE. (反面沉头单+0.00，锣深0.00) (POCKET, MILL DP0.00 TOP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:- (INSERT HL, CNC MILL THRU. S+0.00)X:-（入子孔,正面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 TOP SIDE)X:-（入子孔,反面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 OPP. SIDE)X:-0.00（插针孔,铰)单+0.00X:-0.00（REAM S+0.00 FOR PILOT PIN)X:-0.00（插针孔,割)单+0.00 (正面沉头0.00*0.00深)X:-0.00（W/C S+0.00 FOR PILOT PIN) (0.00 CBORE DP0.00 TOP SIDE) X:-0.00（插针孔,钻穿) (正面沉头0.00*0.00深)X:-0.00（DR.THRU S+0.00 FOR PILOT PIN) (0.00 CBORE DP0.00 TOP SIDE) X:-（冲头过孔,割)单+0.00 (正面避空，CNC单+0.00，锣深0.00) (阴影部分扣位正面锣深0.00)X:-（W/C S+0.00 FOR PUNCH CLEARANCE HL) (POCKET, CNC DP 0.00 S+0.00 TOP SIDE) (POCKET SHADE FOR HEAD, DP0.00 TOP SIDE) X:-（冲头过孔,锣穿)单+0.00 (正面避空，CNC单+0.00，锣深0.00)X:-（MILL THRU. S+0.00 FOR PUNCH CLEARANCE HL) (POCKET DP0.00 CNC S+ TOP SIDE)X:-（异形冲孔,直x斜x,割)单+0.00 (双线部分，割)单+0.00X:-（W/C FOR SPECIAL HL, 0.00 LAND 0.00 TAPER, S+0.00) (W/C PER DOUBLE LINE S+0.00)X:-（冲孔,直x斜x,割)单+0.00X:-（W/C FOR PIERCE DIE HL, 0.00 LAND 0.00 TAPER S+0.00)X:-（冲孔,割)单+0.00X:-（W/C FOR PIERCE DIE HL S+0.00)X:-0.00（冲孔漏屎,钻穿)X:-0.00 (DR. THRU FOR CHUTE)X:-（异形冲孔漏屎,CNC单+0.00,锣穿）X:-0.00 (MILL. THRU FOR SPECIAL CHUTE S+0.00)X:-（产品落料斜度，实数斜30锣）X:-（MILL 30 TAPER FOR PART RAMP NO CLEARANCE)X:-（漏屎斜度，直x斜45锣）X:-（MILL FOR CHUTE 0.00 LAND 45 TAPER)专心-专注-专业