Category6CopperCablesLastStand

Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Category 6 Copper Cables Last Stand,By Frank Bisbee,1,Before we start,VDV/IBS Conference attendees,Our job is to deliver a quality presentation.,Your task is to gather valuable information.,If you finish before me,Please leave the room quietly,So you dont wake the others,2,FAQ,Q:,What is the difference between Cat3, Cat5, Cat5e, Cat6, etc.?,A:,This is actually a somewhat complex question to answer as it involves a number of technical details. The most basic answer is that each Category of cable is supposed to meet (or exceed) a specific set of standards, the most significant of which, is the ability to pass all signals up to a particular carrier frequency (or signaling rate). Additional standards have to be met include values for attenuation, near end cross talk (NEXT), ACR, etc.,Below is a table of the types of Category Cable we install. The table shows the Maximum Carrier Frequencies required by the EIA/TIA 568 Standards for each category of cable and the Maximum Frequencies the manufacturer actually tests the cable to.,Category,Typical Applications,Frequency Required,Tested to,EIA/TIA Ratified Standard?,Cat 3,Voice,16 MHz,16 MHz,Yes,Cat 5,Voice, Data (10/100 Mbps Ethernet),100 MHz,100 MHz,Yes,Cat 5e,Voice, Data (10/100 Mbps/ Gigabit Ethernet),100 MHz,200 MHz,Yes,Cat 5 ENH,1,Voice, Data (10/100 Mbps/ Gigabit Ethernet),*,350 MHz,See note 1.,Cat 6,2,Voice, Data (10/100 Mbps/ Gigabit Ethernet),200(250?) MHz,500 MHz,Draft,1 Cat 5 ENH is another version of Cat 5e offered by the manufacturer we use that further exceeds the Cat 5e EIA/TIA Standard. 2 The Cat 6 Standard has not yet been officially ratified by the EIA/TIA so the specs used by the manufacturer to claim the cable is Cat 6 are based on the current draft of the Standard.,3,WARNING,Cabling installation is not for the untrained,CAT6 cabling systems are CRAFT INTENSIVE,Extreme care must be used when installing or servicing CAT6 cable systems,MARCS = Moves, Adds, Removals, & Changes demand the same level of care,Our surveys indicate this is a universal rule for all (Vendors) CAT6 cabling systems,4,Why do I need all the bandwidth of category 6? As far as I know, there is no application today that requires 200 MHz of bandwidth.,Bandwidth precedes data rates just as highways come before traffic. Doubling the bandwidth is like adding twice the number of lanes on a highway. The trends of the past and the predictions for the future indicate that data rates have been doubling every 18 months. With additional throughput requirements right around the corner, it makes sense to plan ahead.,Note: Bandwidth is defined as the highest frequency up to which positive power sum ACR (attenuation-to-crosstalk ratio) is greater than zero.,5,The barrier of obsolescence is the point where the functionality of copper based communications cabling can no longer deliver the required speeds of the network.,For many years the communications industry has guessed at the maximum effective speed of copper (UTP) cabling. Today many experts are in agreement that the need for speed is approaching coppers max. We must begin to look at hybrid designs that incorporate new technologies mixed with the traditional copper UTP.,6,Network,Cable,Category 5 Cable,(UTP) (Unshielded Twisted Pair) A multipair (usually 4 pair) high performance cable that consists of twisted pair conductors, used mainly for data transmission. Note: The twisting of the pairs gives the cable a certain amount of immunity from the infiltration of unwanted interference. category-5 UTP cabling systems are by far, the most common (compared to SCTP) in the United States. Basic cat 5 cable was designed for characteristics of up to 100 MHz. Category 5 cable is typically used for Ethernet networks running at 10 or 100 Mbps.,Category 5 E Cable,(enhanced) Same as Category 5, except that it is made to somewhat more stringent standards (see comparison chart below). The Category 5 E standard is now officially part of the 568A standard. Category 5 E is recommended for all new installations, and was designed for transmission speeds of up to 1 gigabit per second (Gigabit Ethernet).,Category 6 Cable,Same as Category 5 E, except that it is made to a higher standard (see comparison chart on next slide). The Category 6 standard is now officially part of the 568A standard.,Category 7 Same as Category 6, except that it is made to a higher standard (see comparison chart below). The Category 7 standard is still in the works (as of this writing) and is not yet part of the 568A standard. One major difference with category 7s construction (as compared with category 5, 5 E, and 6) is that all 4 pairs are individually shielded, and an overall shield enwraps all four pairs. Category 7 will use an entirely new connector (other than the familiar RJ-45).,7,CAUTION,Cabling installation is not for the untrained,CAT6 cabling systems are CRAFT INTENSIVE,Extreme care must be used when installing or servicing CAT6 cable systems,MARCS = Moves, Adds, Removals, & Changes demand the same level of care,Our surveys indicate this is a universal rule for all (Vendors) CAT6 cabling systems,8,If we use a Cat 5e RJ45 connector and connect it to a Cat 6 UTP cable, will the installation be Cat5e or Cat 6?,By definition (of the standard), it will be a Cat 5e channel. The actual performance will probably be somewhat better, but nowhere near Cat 6 requirements.,Of course, you can set up a channel using any components and measure it using a Cat 6 (level III) compliant tester, and if it passes, it is Cat 6 performance compliant. It would not be standards compliant however, because the components have requirements in and of themselves to assure interoperability with other Cat 6 components.,Category 6 cabling recognizes advances in cabling technology and is designed to be backward compatible with Categories 3, 5 and 5e. This ensures that any applications that operate on lower category cabling will be fully supported by Category 6 cabling. When different category components are mixed with Category 6 components, the resultant cabling will satisfy the category transmission requirements of the lower performing component.,9,Is there a limitation on the size of bundles one can have with category 6? Can you have 200-300 and still pass category 6?,MAYBE NOT!,There is no limit imposed by the standards,on the maximum number of Category 6 cables in a bundle. This is a matter for the market and the industry to determine based on practical considerations. It should be pointed out that after six or eight cables, the performance in any cable will not change significantly since the cables will be too far away to add any additional external (or alien) NEXT.,What is the shortest link that the standard will allow?,There is no short length limit. The standard is intended to work for all lengths up to 100 meters. There is a guideline in ANSI/TIA/EIA-568-B.1 that says the consolidation point should be located at least 15 meters away from the telecommunications room to reduce the effect of connectors in close proximity. This recommendation is based upon worst-case performance calculations for short links with four mated connections in the channel.,10,SPECIAL NOTICE,Cabling installation is not for the untrained,CAT6 cabling systems are CRAFT INTENSIVE,Extreme care must be used when installing or servicing CAT6 cable systems,MARCS = Moves, Adds, Removals, & Changes demand the same level of care,Our surveys indicate this is a universal rule for all (Vendors) CAT6 cabling systems,11,Are the connectors for category 5e and category 6 different? Why are they more expensive?,Although Category 6 and Category 5e connectors may look alike, Category 6 connectors have much better transmission performance. For example, at 100 MHz, NEXT of a Category 5e connector is 43 decibels (dB), while NEXT of a Category 6 connector is 54 dB. This means that a Category 6 connector couples about 1/12 of the power that a Category 5e connector couples from one pair to another pair. Conversely, one can say that a Category 6 connector is 12 times less noisy compared to a Category 5e connector. This vast improvement in performance was achieved with new technology, new processes, better materials and significant R&D resources, leading to higher costs for manufacturers.,Will contractors be able to make their own patch cords?,Category 6 patch cords are precision products, just like the cables and the connectors. They are best manufactured and tested in a controlled environment to ensure consistent, reliable performance. This will ensure interoperability and backward compatibility. All this supports patch cords as a factory-assembled product rather than a field-assembled product.,12,You can certainly do that, but you will find that a fiber system is still very expensive. Ultimately, economics drive customer decisions, and today optical fiber together with optical transceivers is about twice as expensive as an equivalent system built using Category 6 and associated copper electronics. Installation of copper cabling is more craft-friendly and can be accomplished with simple tools and techniques. Additionally, copper cabling supports the data terminal equipment (DTE) power standard developed by IEEE (802.3af). PCs ship with copper network interfaces included, in fact, recent announcements indicate that the major PC vendors are shipping 10/100/1000 with all new systems. Moving to fiber would mean buying a fiber-based network card to replace equipment already included in the PC.,Why wouldnt I skip category 6 and go straight to optical fiber?,13,When should I recommend or install category 6 vs. category 5e?,From a future proofing perspective, it is always better to install the best cabling available. This is because it is so difficult to replace cabling inside walls, in ducts under floors and other difficult places to access. The rationale is that cabling will last at least 10 years and will support at least four to five generations of equipment during that time. If future equipment running at much higher data rates requires better cabling, it will be very expensive to pull out Category 5e cabling at a later time to install Category 6 cabling. So why not do it for a premium of about 20 percent over Category 5e on an installed basis?,14,Which standard addresses the combination of electrical cable and Cat 6 regarding performance or sensitivity?,Im an ICT Consultant for a university and in process of designing the infrastructure for them. They are using Cat 6 cable as horizontal cabling and fiber optic as backbone. We are facing a problem with M & E consultant on the trunking design. They are proposing the use of a 4-way service box which contains cables for electrical and Cat 6. We cannot find in the standard about the combination of electrical cable and Cat 6 cabling either of performance or sensitivity.,TIA/EIA-569 Commercial Building Standard for Telecommunications Pathways and Spaces includes all necessary provisions for service boxes and enclosures. There are no special considerations associated with Cat 6 cabling.,15,IMPORTANT,Cabling installation is not for the untrained,CAT6 cabling systems are CRAFT INTENSIVE,Extreme care must be used when installing or servicing CAT6 cable systems,MARCS = Moves, Adds, Removals, & Changes demand the same level of care,Our surveys indicate this is a universal rule for all (Vendors) CAT6 cabling systems,16,TESTING,Copper verification: it pays,For datacom installers, copper verification has become part of daily testing for good reason: it pays to verify before you certify. For network owners and installers who are constantly s cubes and stations and making other infrastructure changes, Fluke Networks provides the troubleshooting tools to master cabling installation and subsequent adds, moves and changes. Our tools are ideal for verifying Cat 5, 5e, 6, twisted pair, coaxial cabling and security wiring, covering a broad range of physical media that is typically installed in commercial and residential buildings.,Total integration. Total control. Total Network SuperVision. Thats Fluke Networks promise to you.,New! 2003 Network SuperVision Solutions Catalog for the Copper and Fiber Cabling Infrastructure- take a look at the most comprehensive line of premises network testing solutions (1.6MB),17,List of cables and street prices as of 3/9/2004,Jacksonville, FL,Cat 5e Non Plenum,$66.00,Cat 6 Non Plenum,$98.50,6 Strand Multi-Mode Fiber Non Plenum,$460.00,6 strand Single-Mode Fiber Non Plenum,$220.00,Cat 5e Plenum,$194.00,Cat 6 Plenum,$332.00,6 Strand Multi-Mode Fiber Plenum,$490.00,6 Strand Single-Mode Fiber Plenum,$240.00,Cat 5e Limited Combustible-CMP,$ no price available*,Cat 6 Limited Combustible-CMP,$445.00*,*Passes UL/NFPA 262 & 255 - all FEP construction,Limited Combustible Cable -,NOT IN STOCK,18,19,