注塑专业英语(共11页)

精选优质文档-倾情为你奉上Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE agglomerates etc阻燃剂/PTFE结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra 添加多一点Reduced content减少含量Dropped/reduced by x减少含量Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by 预计在完成Expected order is xMT预计定单量吨Estimated annual/monthly consumption预计年/月用量air vent vale 通气阀 anchor pin 锚梢 angular pin 角梢 baffle 调节阻板 angular pin 倾斜梢 baffle plate 折流档板 ball button 球塞套 ball plunger 定位球塞 ball slider 球塞滑块binder plate 压板 blank holder 防皱压板 blanking die 落料冲头 bolster 上下模板 bottom board 浇注底板 bolster 垫板 bottom plate 下固定板 bracket 托架 bumper block 缓冲块 buster 堵口 casting ladle 浇注包 casting lug 铸耳 cavity 模穴(模仁) cavity retainer plate 模穴托板 center pin 中心梢 clamping block 锁定块 coil spring 螺旋弹簧 cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓 core 心型 core pin 心型梢 cotter 开口梢 cross 十字接头 cushion pin 缓冲梢 diaphragm gate 盘形浇口 die approach 模头料道 die bed 型底 die block 块形模体 die body 铸模座 die bush 合模衬套 die button 冲模母模 die clamper 夹模器 die fastener 模具固定用零件 die holder 母模固定板 die lip 模唇 die plate 冲模板 die set 冲压模座 direct gate 直接浇口 dog chuck 爪牙夹头 dowel 定位梢 dowel hole 导套孔 dowel pin 合模梢 dozzle 辅助浇口 dowel pin 定位梢 draft 拔模锥度 draw bead 张力调整杆 drive bearing 传动轴承 ejection pad 顶出衬垫 ejector 脱模器 ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套 ejector pad 顶出垫 ejector pin 顶出梢 ejector plate 顶出板 ejector rod 顶出杆 ejector sleeve 顶出衬套 ejector valve 顶出阀 eye bolt 环首螺栓 filling core 椿入蕊 film gate 薄膜形浇口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圆形模板 fixed bolster plate 固定侧模板 flanged pin 带凸缘? flash gate 毛边形浇口 flask 上箱 floating punch 浮动冲头 gate 浇口 gate land 浇口面 gib 凹形拉紧? goose neck 鹅颈管 guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶?冲头 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒 hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头 insert 嵌件 insert pin 嵌件梢 king pin 转向梢 king pin bush 主梢衬套knockout bar 脱模杵 land 合模平坦面 land area 合模面 leader busher 导梢衬套 lifting pin 起模顶? lining 内衬 locating center punch 定位中心冲头 locating pilot pin 定位导梢 locating ring 定位环 lock block 压块 locking block 定位块 locking plate 定位板 loose bush 活动衬套 making die 打印冲子 manifold block 歧管档块 master plate 靠模样板 match plate 分型板 mold base 塑胶模座 mold clamp 铸模紧固夹 mold platen 模用板 moving bolster 换模保持装置 moving bolster plate 可动侧模板 one piece casting 整体铸件 parallel block 平行垫块 paring line 分模线 parting lock set 合模定位器 pass guide 穴型导板 peened head punch 镶入式冲头 pilot pin 导? pin gate 针尖浇口 plate 衬板 pre extrusion punch 顶挤冲头 punch 冲头 puncher 推杆 pusher pin 衬套梢 rack 机架 rapping rod 起模杆 re-entrant mold 凹入模 retainer pin 嵌件梢 retainer plate 托料板 return pin 回位梢 riding stripper 浮动脱模器 ring gate 环型浇口 roller 滚筒 runner 流道 runner ejector set 流道顶出器 runner lock pin 流道拉梢 screw plug 头塞 set screw 固定螺丝 shedder 脱模装置 shim 分隔片 shoe 模座之上下模板 shoot 流道 shoulder bolt 肩部螺丝 skeleton 骨架 slag riser 冒渣口 slide(slide core) 滑块 slip joint 滑配接头 spacer block 间隔块 spacer ring 间隔环 spider 模蕊支架 spindle 主轴 sprue 注道 sprue bushing 注道衬套 sprue bushing guide 注道导套 sprue lock bushing 注道定位衬套 sprue puller 注道拉料? spue line 合模线 square key 方键 square nut 方螺帽 square thread 方螺纹 stop collar 限位套 stop pin 止动梢 stop ring 止动环 stopper 定位停止梢 straight pin 圆柱? stripper bolt 脱料螺栓 stripper bushing 脱模衬套 stripper plate 剥料板 stroke end block 行程止梢 submarine gate 潜入式浇口 support pillar 支撑支柱/顶出支柱 support pin 支撑梢 supporting plate 托板 sweep templete 造模刮板 tab gate 辅助浇口 taper key 推拔键 taper pin 拔锥梢/锥形梢 teeming 浇注 three start screw 三条螺纹 thrust pin 推力销 tie bar 拉杵 tunnel gate 隧道形浇口 vent 通气孔 wortle plate 拉丝模板plain die简易模 pierce die冲孔模 forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点 dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印 extension dwg展开图 procedure dwg工程图 die structure dwg结构图 material材质 material thickness料片厚度 factor系数 upward向上 downward向下 press specification冲床规格 die height range适用模高 die height闭模高度 burr毛边 gap间隙 weight重量 total wt.总重量 punch wt.上模重量三、模具 塑料模具mould of plastics 注塑模具injection mould 冲压模具die 模架mould base 定模座板Top clamping plate Top plate Fixed clamp plate 水口推板stripper plate A板A plate B板B plate 支承板 support plate 方铁 spacer plate 底针板 ejector plate 面针板 ejector retainer plate 回针 Return pin 导柱 Guide pin 有托导套 Shoulder Guide bush 直导套 Straight Guide bush 动模座板Bottom clamp plate Moving clamp plate 基准线datum line 基准面datum plan 型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin 单腔模具single cavity mould 多腔模具multi-cavity mould 多浇口multi-gating 浇口gate 缺料starving 排气breathing 光泽gloss 合模力mould clamping force 锁模力mould locking force 挤出extrusion 开裂crack 循环时间cycle time 老化aging 螺杆screw 麻点pit 嵌件insert 活动镶件movable insert 起垩chalking 浇注系统feed system 主流道 sprue 分流道runner 浇口gate 直浇口direct gate , sprue gate 轮辐浇口spoke gate , spider gate 点浇口pin-point gate 测浇口edge gate 潜伏浇口submarine gate , tunnel gate 料穴cold-slug well 浇口套sprue bush 流道板runner plate 排飞槽vent 分型线（面）parting line 定模stationary mould，Fixed mould 动模movable mould, movable half 上模upper mould， upper half 下模lower mould， lower half 型腔cavity 凹模cavity plate，cavity block 拼块split 定位销dowel 定位销孔dowel hole 型芯core 斜销angle pin, finger cam 滑块slide 滑块导板slide guide strip 楔紧块heel block, wedge lock 拉料杆sprue puller 定位环locating ring 冷却通cooling channel 脱模斜度draft 滑动型芯slide core 螺纹型芯threaded core 热流道模具hot-runner mould 绝热流道模insulated runner mould 熔合纹weld line （flow line） 三板式模具three plate mould 脱模ejection 换模腔模具 interchangeable cavity mould 脱模剂release agent 注射能力shot capacity 注射速率injection rate 注射压力injection pressure 差色剂colorant 保压时间holdup time 闭模时间closing time 定型装置sizing system 阴模female mould，cavity block 阳模male mould 电加工设备Electron Discharge Machining 数控加工中心CNC machine center 万能铁床Universal milling machine 卧式刨床Horizontal planer 车床Engine lathe 平面磨床Surface grinding machine 去磁机Demagnetization machine 万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller 超声波清洗机Ultrasonic clearing machine一、 组织机构及职位 XX电子有限公司XX Electronics CO., Ltd 总经理办公室General managers office 企管部Enterprise management department (EM) 行政部Administration department (AD) 销售部Sales department (SD) 财务部Financial department (FD) 技术部Technology department (TD) 物控部Production material control department (PMC) 生产部Production department(PD) 模具部Mold manufacturing department, Tooling manufacturing department (TM) 品管部Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop 装配车间Assembly workshop 模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop 电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop 工磨车间Grinding workshop 总经理General manager (GM) 副总经理Vice-general manager 经理manager 董事长president 副董事长Vice-president XX部门经理Manager of XX department 主任、主管supervisor 拉长Line leader 组长Foreman, forelady 秘书secretary 文员clerk 操作员operator 助理assistant六物控 保质期shelf life ABC分类法ABC Classification 反常需求Abnormal Demand 措施信息Action Message 活动报告标志Action-report-flag 基于活动的成本核算Activity-based Costing (ABC) 实际能力Actual Capacity 实际成本Actual Costs 调整现有库存量Adjust-on-hand 已分配量Allocation 替代工序Alternative Routine 装配订单Assembly Order 装配零件表Assembly Parts List 装配Assembly 计划自动重排Automatic Rescheduling 可达到库存Available Inventory 可用材料Available Material 达到库存Available Stock 可利用工时Available Work 可签约量Available-to-promise 平均库存Average Inventory 欠交订单Back Order 倒序计划Back Scheduling 倒冲法Back flush 未完成订单Backlog 现有库存余额Balance-on-hand Inventory 批号Batch Number 批量生产Batch Production 标杆瞄准Benchmarking 工时清单Bill of Labor 提货单Bill of Lading 物料清单Bill of Material 分库Branch Warehouse 经营规划Business Plan 采购员Buyer 能力管理Capacity Management 能力需求计划Capacity Requirements Planning (CRP) 保管费率Carrying Cost Rate 保管费Carrying Cost 单元式制造Cellular Manufacturing 修改批量日期Change Lot Date 修改工序Change Route 修改产品结构Change Structure 检查点Check Point 闭环物料需求计划Closed Loop MRP 通用工序标识Common Route ID 计算机集成制造Computer-integrated Manufacturing (CIM) 配置代码Configuration Code 约束管理/约束理论Constraints Management/Theory of Constraints (TOC) 依成本的材料清单Costed Bill of Material 急需零件Critical Part 累计提前期Cumulative Lead Time 现有运转时间Current Run Hour 现有运转数量Current Run Quantity 周期盘点Cycle Counting 调整日期Date Adjust 有效日期Date Available 修改日期Date Changed 结束日期Date Closed 截止日期Date Due 生产日期Date in Produced 库存调整日期Date Inventory Adjust 作废日期D ate Obsolete 收到日期Date Received 交付日期Date Released 需求日期Date Required 发货日期Date to Pull 空负荷Dead Load 需求管理Demand Management 需求Demand 实际能力Demonstrated Capacity 非独立需求Dependent Demand 直接增减库存处理法Direct-deduct Inventory Transaction Processing 发料单Disbursement List 派工单Dispatch List 分销资源计划Distribution Resource Planning (DRP) 鼓缓冲绳子Drum-buffer-rope 经济订货批量Economic Order Quantity (EOQ) 工程变更生效日期Engineering Change Effect Date 工程变更生效单Engineering Change Effect Work Order 工程停止日期Engineering Stop Date 例外控制Exception Control 呆滞材料分析Excess Material Analysis 急送代码Expedite Code 加工订单Fabrication Order 补足欠交Fill Backorder 总装提前期Final Assembly Lead Time 确认的计划订单Firm Planned Order 固定订货批量F ixed Order Quantity 集中预测Focus Forecasting 完全跟踪Full Pegging 通用生产管理原则Generally Accepted Manufacturing Practices 毛需求Gross Requirements 在制品库存In Process Inventory 独立需求Independent Demand 投入/产出控制Input/ Output Control 检验标识Inspection ID 厂际需求Interplant Demand 库存周转率Inventory Carry Rate 仓库库位类型Inventory Location Type 库存周转次数Inventory Turnover 发送订单Issue Order 项目记录Item Record 物料项目Item 加工车间Job Shop 准时制生产Just-in-time (JIT) 看板Kanban 人工工时Labor Hour 最后运输日期Last Shipment Date 提前期Lead Time 层Level 负荷量Load Leveling 负荷报告Load Report 负荷Load 仓位代码Location Code 仓位备注Location Remarks 仓位状况Location Status 按需订货Lot for Lot 批量标识Lot ID 批量编号Lot Number 批量Lot Size 低位码Low Level Code 机器能力Machine Capacity 机器加载Machine Loading 外购或自制决策Make or Buy Decision 面向订单生产的产品Make-to-order Product 面向库存生产的产品Make-to-stock Product 制造周期时间Manufacturing Cycle Time 制造资源计划Manufacturing Resource Planning (MRP II) 主生产计划Master Production Schedule (MPS) 物料成本Material Cost 物料发送和接收Material Issues and Receipts 物料需求计划Material Requirements Planning (MRP) 登陆标志MPS Book Flag MPS 多重仓位Multiple Location 净改变式MRP N et Change MRP 净需求Net Requirements 新仓位New Location 新组件New Parent 新仓库New Warehouse 不活动报告No Action Report 现有库存量On-hand Balance 未结订单Open Order 订单输入Order Entry 订货点Order Point 订货方针Order Policy 订货承诺Order Promising 订货备注Order Remarks 双亲Parent 零件清单Part Bills 零件批次Part Lot 零件编号Part Number 零件Part 反查Pegging 领料单Picking List 领料/提货Picking 计划订单Planned Order 后减库存处理法Post-deduct Inventory Transaction Processing 前减库存处理法Pre-deduct Inventory Transaction Processing 发票价格Price Invoice 采购订单价格Price Purchase Order 优先计划Priority Planning 产品控制Product Control 产品线Production Line 生产规划编制Production Planning 产品率Production Rate 产品结构树Production Tree 预计可用库存Projected Available Balance 采购订单跟踪Purchase Order Tracking 已分配量Quantity Allocation 仓位数量Quantity At Location 欠交数量Quantity Backorder 完成数量Quantity Completion 需求量Quantity Demand 毛需求量Quantity Gross 进货数量Quantity In 排队时间Queue Time 队列Queue 重生成式MRP Regenerated MRP 重排假设Rescheduling Assumption 资源需求计划Resource Requirements Planning 粗能力计划Rough-cut Capacity Planning 工艺路线Routing 安全库存量Safety Stock 保险期Safety Time 预计入库量Scheduled Receipt 残料率Scrap Factor 发送零件Send Part 维修件Service Parts 发货地址Ship Address 发货单联系人Ship Contact 发货零件Ship Date 发货单Ship Order 工厂日历Shop Calendar 车间作业管理Shop Floor Control 损耗系数Shrinkage Factor 标准产品成本Standard Product Cost 标准机器设置工时Standard Set Up Hour 标准单位运转工时Standard Unit Run Hour 标准工资率Standard Wage Rate 状况代码Status Code 库存控制Stores Control 建议工作单Suggested Work Order 约束理论Theory of Constraints (TOC) 时间段Time Bucket 时界Time Fence 单位成本Unit Cost 采购计划员Vendor Scheduler 采购计划法Vendor Scheduling 工作中心能力Work Center Capacity 工作中心Work Center 在制品Work in Process 工作令跟踪Work Order Tracking 工作令Work Order 工作进度安排Work Scheduling 零库存Zero Inventories 经济订货批量Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本) 美国生产和库存控制协会APICS，American Production & Inventory Control Society二、 产品 连接器connector 端子terminal 条型连接器bar connector 阴连接器Housing 阳连接器wafer 线束wire harness 间距space 额定电压 rated voltage 额定电流 rated current 接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage 针pin 物料编号part number 导线wire 基体金属Base metal 电缆夹cable clamp 倒角chamfer 接触面积contact area 接触件安装孔contact cavity 接触长度contact length 接触件电镀层contact plating 接触压力contact pressure 接触件中心距contact space 接触簧片contact spring 插孔socket contact 法兰、凸缘Flange 界面间隙interfacial gap 键Key 键槽keyway 过渡段ramp 屏蔽套shielding 定位基准Datum reference 扁平电缆flat cable ，Ribbon cable 柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printed circuit 焊盘pad 图形pattern 间距pitch 负极Negative pole 正极positive pole 回流Reflow 原理图Schematic diagram 单面板single sided board 双面板Two-sided board，Double-sided board 表面安装surface Mounting 翘曲warp， bow 波峰焊wave soldering 编织层braid 同轴电缆coaxial cable 电介质dielectric 电缆中导线的头数ends 外部干扰external interference 填充物filler 护套jacket 比重specific gravity 电阻的温度系数Temperature coefficient of resistance三、 品管 SPC statistic process control 品管保证Quality Assurance 品管控制Quality control 来料检验IQC Incoming quality control 巡检IPQC In-process quality control 校对calibration 动态试验dynamic test 环境试验Environmental test 非破坏性试验non-destructive test 光泽gloss 击穿电压(dielectric) breakdown voltage 拉伸强度tensile strength 冷热骤变试验thermal shock test 环境试验炉Environmental chamber 盐雾实验salt spray test 绝缘电阻测试验仪Insulating resistance meter 内应力internal stress 疲劳fatigue 蠕变creep 试样specimen 撕裂强度tear strength 缩痕shrink mark, sink mark 耐久性durability 抽样sampling 样品数量sample size AQL Acceptable Quality level 批量lot size 抽样计划sampling plan OC曲线operation curve 试验顺序sequence of tests 环境温度ambient temperature 可焊性solderability 阻燃性flame resistance四、 生产 注塑机injection machine 冲床Punch machine 混料机blender mixer 尼龙nylon 黄铜 brass 青铜 bronze 紫(纯)铜 copper 料斗hopper 麻点pit 配料compounding 涂层coating 飞边flash 预热preheating 料reworked material 塑料reworked plastics 工艺设计process design 紧急停止emergency stop 延时time delay七QS-9000中的术语 APQP Advanced Product Quality Planning and Control Plan，产品先期策划和控制计划 PPAP Production Part Approval Process,生产件批准程序 FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析 Injection machine 啤机Shot size（weight） 实际射胶量 injection volume 理论射胶量 min mold height 最小容模厚度 Max mold height 最大容模厚度 Tie bar clearance 拉杆间距 Die plate size 模板尺寸 Ejector stroke 顶出行程 barrel 炮筒，机筒 clamp force 锁模力 non-return valve 止回阀 shear 剪切 opening 开模行程 Injection pressure 射胶压力 back pressure 背压 nozzle size 射咀尺寸 Cycle time 循环周期 down time 停机时间 hopper 料筒 Mold release 脱模剂 lubrication 润滑 work horse 主力，主要设备Reserve pressure/packing pressure保压 mold trial 试模 shot （一）啤Decompress 减压 oven 烤炉，烘灶 shrinkage rate 收缩率 Residence time 滞留时间 injection speed 注射速度 booster time 增压时间 Compression ratio 压缩比 mold close time 合模时间 Resin 胶料Plastification 塑化，增塑 viscosity 粘性，粘度 contamination 污染，杂物Thermoplastic 热塑性塑料 thermosetting plastics 热固性塑料 Booster time 增压时间 feed 喂料，填充 purge 净化 Flame retardant 阻燃 degradation 降解，软化 regrind 再粉碎 Water absorption 吸水 reinforce 增强，加固 specific gravity 比重Elongation 延伸率 density 密度 melting point 熔点 Polystyrene 聚苯乙烯（PS） Styrene 苯乙烯 Acrylonitrile 丙烯腈 Polypropylene 聚丙烯（PP） Polyethylene 聚乙烯 glass fiber 玻纤 Condensation 凝固，浓缩 crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢 tool steel 模具钢 Free-cutting steel 高速切削钢 case hardening steel 表面硬化钢 Pre-hardened steel 预硬钢 ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金 high speed steel 高速钢 cast iron 铸铁 Steel specification 钢材规格 steel certification 钢材合格证明书 Stainless steel 不锈钢 nickel 镍 chrome 铬 aluminum 铝 Copper 铜 brass 黄铜 bronze 青铜 titanium 钛Processing 钢材的加工方法Harding / quench 淬火 nitride 氮化 temper 回火 anneal 退火 Roll 轧制 abrasive 研磨，磨损的 finish 精加工，抛光（polish）Case-hardening 表面硬化 milling machine 铣（锣）床Lathe车床 drill 钻床 wire cut 线割 NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工 Cut steel 开料 Precision ground 精密研磨 heat treatment 热处理 tap 丝锥，攻牙 Texture 蚀纹 weld 焊接 forge 锻压 deformation 变形Spraying 喷涂 die-cast 压铸Properties 性能Resistance 电阻，抵抗能力 abrasion / wear磨损 erode / corrode 腐蚀 Toughness 韧性 yield strength 屈服强度 tensile strength 拉伸强度 Fatigue strength 疲劳强度 break 断裂 stress 应力 hardness 硬度 Humidity / moisture 潮湿，湿气 roughness 粗糙度 parameter 参数Thermal conductivity 导热系数 manufacture 制造，加工 drawback 缺点 Ductility 延展性 grain 晶粒 property 性能，财产 brittleness 脆性GD&T （Geometric Dimensions and Tolerance ） 形位尺寸公差 Flexural strength 挠曲强度 impact 冲击 conductivity 传导性，导电性 Optical 光学的 transparent 透明的 insulation 绝缘Mechanical 机械的 processability 可加工性能 timeyield 蠕变 Physical 物理的 flow rate 流动速率 compressive strength 压缩强度 Adhesive 粘附的，胶合 durability 耐用性Mold design 模具设计Tooling specification 模具规格 mould flow 流动模拟 sprue nozzle 唧咀孔 Clearance 避空，间隙 undercut 倒扣 flush 插入，埋入 legend 图例 Groove 凹槽 latch 插销 class 类型，种类 plan 平面图Orifice 孔，口 column 柱位 boss 凸台 standard 标准，规格 Rib 骨位 tapered interlock 锥形管位块 Bubbler 炮隆 Bolt 螺钉，销顶 identification mark 铭牌 P/L strip 锁模片 Overflow well / cold-slug well 冷料井 Vent 排气 pocket 槽 Gate location 入水点 full line 实线 broken line 虚线 Retainer 固定，支撑 operator 操作者（啤工） receptacle 插座Lifting hole 吊令孔 insulation plate 隔热板 cavity number 型腔号 Bolster 支撑，垫子 vent channel 排气槽 leak / filter 渗漏 Leak test 试运水 stamp / engrave 雕刻，印记（打字唛） Clamp slot 码模槽 support button / pin 垃圾钉 cut steel 开料 Lodge 安装，放置 inlay 镶嵌，插入 cam / lifter 斜顶 Stripper推方 lifting bar 吊模方 sprue 唧咀 tolerance 公差 Counter bore 沉孔 slant 倾斜，斜面 conical 圆锥的，圆锥形的Bolt 螺栓 manifold 热流道板 prototype tooling 原型试验 Gusset 角撑 reverse mold 倒装模 constrain / restrict约束，限制 Counter lock 反锁 thermocouple 热电偶 moldmaker 模具制造商 Asset / property number 资产编号 tool product destination 模具生产地点 Accelerating ejection 加速顶出 hydraulic 液压的 pneumatic 气动的 Trapezoid 梯形的 semi-round 半圆形 f