R&S基础培训

Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,RFMD CTS Training,40,of,40,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,R&S Training,Agilent 33120A-,函数,/,任意波形发生器,ARB, MFS,产生低频信号，生成,trigger,等,GPIB,地址：,12,Agilent,E4418B-,单通道功率计,实现快速、精确和可重复的功率测量。,GPIB,地址：,13,Agilent,E4412A-POWER SENSOR,E4412A,功率传感器能够测量,10 MHz,至,18 GHz,频率范围内和,-70,至,+20 dBm(90 dB,动态范围,),功率范围之内的平均功率。,Agilent 11713A-,开关驱动器,Agilent 11713A,衰减器,/,开关驱动器为程控衰减器和机电开关提供了,GPIB,和“本地”前面板驱动控制。,Agilent 8904A-,Multifunction Synthesizer, DC-600 KHz,600 kHz,正弦波，,50 kHz,方波、斜波和三角波,12,位直接数字合成,话音、,DTMF,、数字、,Hop Ram,序列模式,AM,、,FM,、,Phi-M,、,DSBSC,和脉冲调制,单元到单元相位同步,GPIB,地址：,26,Switch Panel,Switch 0,Switch9,VSA2,Trigger,VSA1,Trigger,ARB Trigger,BNC Connector DAQ,测试电压,BNC-2090,连接电脑上的,PCI-6052,卡,BNC-2090,Buffer Box,与,UTI,的连线,(,前面板,),Buffer Box,UTI,Buffer Box,的“,WRITE,”,Port,链接,UTI,的“,WRITE,”,Port,Buffer Box,的“,READ,”,Port,链接,UTI,的“,READ,”,Port,Agilent E4432B,信号发生器,输出指定频率高频信号,250kHz,至,3GHz,频率范围,GPIB,地址：信号源,1,是,19,信号源,2,是,20,Agilent E4438C,信号发生器,输出指定频率高频信号,250kHz,至,4GHz,频率范围,GPIB,地址：信号源,1,是,19,信号源,2,是,20,怎样查看信号源的,Option,1.,在信号源初始界面中,按下“,Local,”键,2,.,按下“,Utility,”键,3,.,按下“,Instrument Info/Help Mode,”键,4.,按下“,Options Info,”键,5,.,屏幕显示的就是当前 这块信号源所具备的,Options,Agilent E4406A,矢量信号分析仪,Agilent E4406A,矢量信号分析仪（,VSA）,系列发射机测试仪是全功能的矢量信号分析仪,GPIB,地址,:,VSA1,是,18,IP,地址是,172.30.1.2,VSA2,是,15,IP,地址是,172.30.1.3,怎样查看,VSA,的,Option,1.,在初始界面中按下“,System,”键,2,.,按下“,More,”键,3,.,按下“,Show System,”键,4,.,屏幕上显示的就是此,VSA,所具备的,Options,5,.,按下“,Next Page,和,Prev Page,”键，上下翻页来查看,Options,未安装的,Option,已安装的,Option,生产线上最常用的两种,Option,：,BAF(WCDMA),和,202(EDGE),RF AMPLIFIER-,功率放大器,为,RF,信号提供放大的作用,Agilent 66332,A-,动态测量直流电源表,GPIB,地址：,PowerSupply1,为,5,PowerSupply2,为,6,Agilent 66332,A,背面连线图,如何用,National Instruments,软件查找各仪表的,GPIB,地址,单击 “,Start,”,“,All Programs,”,“,National Instruments,”,“,Measurement & Automation,”进入程序,单击“,GPIB0(PCI-GPIB),”,点击“,Scan For Instruments,”按钮后，程序会自动扫描所有,(,正确连接,GPIB,线,),的,仪表。,所有仪表的,GPIB,地址和信息都会显示在屏幕上,GSM EDGE UTI-3,Tester(,正面,/,背面,),Ref,连线,1.,用一块仪表做,Ref Out,2.,其他仪表都做,Ref In,Trig,连线,1,.,信号源,19(PATT Trig in),与,VSA18(Trigger in),相连，再连接到,SWITCH,面板上,2.,信号源,20(PATT Trig in),与,VSA15(Trigger in),、,Buffer Box,相连，再连接到,SWITCH,面板上,3.33120A,接到,SWITCH,面板,4.,如果更换仪表地址，必须是,19,连接,18,，,20,连接,15,CDMA Tes,ter(,正面,/,背面,),Ref,连线,与,GSM EDGE UTI-3,Tester,连线基本一样，只是最后把,33120A,的,Ref,再连接到,Switch,后面板上,Trig,连线,1,.,信号源,19(PATT Trig in),与,VSA18(Trigger in),相连，再连接到,SWITCH,面板上,2.,VSA18(Trigger in),连接到,33120A,