常用塑料英文单词

常用塑料英文单词嵌件-insert嵌件销-insert pin 气胀真空成形-air assist forming 空气隙-air gap 空气顶出-air ejection 永久伸长-permanent elongation,tension set 永久变形-permanent set,permanent deformation 蚀刻,侵蚀-etching 应力-stress应力松弛-stress relaxation应力龟裂-stress cracking应力集中-stress concentration 应力断裂,应力破坏-stress rupture 应力.应变曲线-stress-strain curve 应力.应变图-stress-strain diagram 托板,模板-retainer plate 硬度-hardness合模机构-mold clamping mechanism 合模力,闭模力-locking force,clamping force 开模力-mold opening force 悬臂梁-cantilever beam 润滑剂-lubricant 模具-mold,Tools,Tooling 模温度控制器-mold temperature controller 模具尺寸-mold size 加热管套（料筒）-heating cylinder 加热板-heating plate 凸轮-cam玻璃纤维-glass fiber,fibrous glass玻璃纤维强化热塑塑料-fiber glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP玻璃纤维强化塑料 -glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP.感光聚合物-photopolymer,photo-sensitive polymer 镜面抛光-mirror polishing 龟裂-cracking龟裂-crack 颗粒料-granule 石墨-graphite 石墨纤维-graphite fiber 间隙, 隙距-clearance 模蕊,蕊片,蕊线,蕊孔-core 成孔销,模蕊销-core pin 成孔销托板-core pin plate 公差,容差-tolerance 冷料-cold slug 冷料井,冷料窝-cold slug well 回程销,覆归销-surface pin 冷热骤变试验-thermal shock test 热应力龟裂-thermal stress cracking,TSC 侧向浇口-side gate 侧向模蕊（心型）销-side draw pin 砂磨-sanding 喷砂,打砂-sand blast 修饰,涂饰,打光-finishing 自断浇口,剪切浇口-shear gate 紫外线-ultraviolet, UV 紫外线稳定剂-UV stabilizer 紫外线吸收剂-UV absorber 压花-embossing 压花机-embossing machine 喷霜,起霜-blooming exudation 鲨皮斑-shark skin 射出压力-injection pressure 射出成形-injection molding 射出成形机-injection molding machine 射出成形模具-injection mold 射出装置-injection unit 射出速度-injection speed 射出喷嘴,注料嘴-injection nozzle 射出容量-machine shot capacity 射出率（量）-injection rate 煮沸试验-boiling test 充填不足,缺料-short shot手动模具-hand mold,loose mold 手动油压机-hand press 缩窝,凹孔-shrinkage pool 冲击试验-inpact test 冲击强度-impact strength 烧结法,粉铸法-sintering 烧结成形法-sinter molding 模板-mold plate 注射,射料-shot 硅橡胶-silicone rubber 真空成形-vacuum forming 珠光颜料-pearlescent pigment 浸渍涂装-dip coating 人造皮革-artificial leather废料粉碎机-scrap grinder 顶出板,脱模板-stripper plate 应力龟裂-stress cracking 环境应力龟裂试验-environmental stress cracking test 行程,冲程-stroke注道衬套,浇口衬套 成形压力,模制压力 成形温度,模制温度 成形循环,成形周期 成形时间,模制时间 成形收缩,模压收缩 窄浇口,限制形浇口 剪切强度,抗剪强度注道,注道料-sprue-sprue bush-molding pressure-molding temperature-molding cycle-molding time-mold shrinkage, molding shrinkage -restricted gate-shear strength增亮剂-brightening agent,optical brightener,optical whitening agent加速试验-accelerated test加速老化-accelerated ageing 塑性变形-plastic deformation 塑性流动-plastic fiow 翘曲-warp(ing),warpage 抗臭氧性-ozone resistance抗臭氧试验-ozone resistance test耐天侯性-weatherability,weather resistance 耐旋光性-light resistance,light fastnessPOEuoE(oodaposa_6.E15_do.lloao鏗NlaEQlnp本6.EPOU1 U.21O.2.EEnssald so-!s aaoetnco=nplls来 poi0,leq lnoMOOUMIfc鰹罂fcaK snd InofQOUMolo一do5.2.elaMoa如剧ag u.21善舊 m6utasu- o一uose.43瑶翠垢(* 6.EPOE -oils鱼 qnoplm掘却猱題摆 POE Alseo=3ull*K& 8us.2p -leqellffiEfc斜eq.2一蛊斜 aouss 一 sai uosotoolffi uope.looQ.csPG.Eps.專 8u2.c2coauoedlu!ffl屯* gujscomol poelfflffi lcos6.EaeaM瀏苫霞H.Er囁吕|藝規总刪蚁軒6uEnq来鬻專_s 6uEnq=nq綜烬来鬻 a6uods(nOR(osd(nORSsde3=8co0 弔_d paule(og祠ad Papuedxuleo4 scmsad劉爆嘤- amssaid Moeqlsqv 厘 回 qr alncocoald Moeqlw* zzou煤 qr 響鰹 6uzon _nnog!1b aNzoulB妲B鰹 lualuoE u.2siz1S9 uo爾隼ffia uou嶽对快咚UOAU 丄修边,除边-deflashing,definning 修边机,修毛边机-deflasher 手工脱模,手工顶出-hand ejection 剥离,剥皮加工-peeling 剥离试验-peeling test 拉出成形-pultrusion 凹痕,缩痕-sink mark,shrink mark 抗刮硬度,刮痕硬度-scratch hardness 非破坏性试验-non-destructive testing 起泡,气泡-blister 疲劳试验-fatigue test 疲劳寿命-fatigue life 疲劳强度-fatigue strength 针眼,针孔-pinhole 玻璃纤维强化,热塑塑料射出成形-fiberfil molding 起泡,气泡-blister 底漆,底胶,引发剂-primer 溢料-flash 溢料缝,毛边槽-flash groove 流痕-flow mark 冷却线-frost line 原型模,试验模-prototype mold 环境温度-ambient temperature 止流阀-shut-off valve 孔隙,空洞,气泡-void 放电-discharge 全压式模具-positive mold 辅助压缸-auxiliary cylinder 烫印-hot stamping,roll leaf stamping 弯曲龟裂-flex cracking 磨损-abrasion,wear 磨耗-abrasion loss 莫斯硬度-Mohshardness 退火-annealing 回火-tempering 杨氏弹性系数-Youngs modulus of elasticity 油压增压器-hydraulic intensifier 油压机-hydraulic press油压马达-hydraulic motor 焊接-welding 内衬,衬套,衬垫-liner 流道,流道料-runner 合模销,导销-leader pin 合模销套,导销衬套-leader pin bushing 回程销, 覆归销-return pin 冷却水通路-cooling channel 常温成形,冷模压-cold molding 老化试验-ageing test 对位圈,定位环-locating ring 熔合线,结合线-weld line 肉厚-wall thickness 脱模斜度-draft angle 母模-cavity side 顶出销,顶针-ejector pin 分模线-parting line 浇口,灌点-gate 竖浇道-sprue 浇道,流道-runner 模仁,雄模,模心-core side 浇口白晕-gate bush 凹痕,缩痕,缩水-sink mark 银线-silver line 隧道形浇口-tunnel gate 沉陷式浇口,潜入式浇口-submarine gate 针孔形浇口-pin point gate 注道形浇口,直接浇口-sprue gate 毛边形浇口,薄膜形浇口-flash gate,external ring gate,internal ring gate 喷流,喷射现象-jetting 剥料板-stripper plate