钻井专用中英文对照

英文钻井日志常用缩写词汇英文钻井日志常用缩写词汇（按照钻井施工顺序排列）DC-drill collar钻铤DP-drill pipe钻杆TD-true depth垂直井深TD-total depth总进尺，总深度USG-united statesgallon美制加仑Hrs-hours小时Drlg-drilling钻进，钻井Circ-circulating循环Hi. Vis.-high viscosity高粘度CSG-casing套管POOH-pull out of hole起钻R/U-rig up安装SXS-sacks袋子WOC-wait on cement候凝MW-mud weight泥浆比重N/U-nipple up安装P/U-pick up上提，提起TIH-trip in hole下钻Cmt-cement水泥DCS-drill collar stem钻铤柱ISF-induction-spherically focused log感应-球形聚焦测井LSS-long-spacesonic (log)长源距声波测井GR-gamma ray log自然伽马测井LCST-lower critical solution temperature地临界溶液温度R/D-rig downN/D-nipple downBOPs-blowout preventerstackM/U-make-upBHA-bottom hole assemblyPV-plastic viscosityYP-yield pointSols-solidsPH-acidity or alkalinityCond.-conditionedLOT-leak-off test破裂压力试验EMW-equivalent mud weightROP-rate of penetrationFPH-feet per hourWL-water lossB/U-bring-upKCL-potassiumStds-standsJB-junk basketL/D-lay downRIH-run in holeGB-globe basketJts-jointsBttm-bottomWt-weightWOB-weight on bitDLL-dual later log拆卸设备卸下来，拆卸防喷器组合结构上扣，连接，接单跟下部钻具结构塑性粘度屈服点，流动点固相含量酸碱度处理，调整地层抗破强度试验，套管鞋下边当量泥浆比重机械钻速英尺 /小时滤失量，失水暂停，是停止，中断氯化钾钻杆或钻铤立柱随钻打捞杯卸下，甩下，放下下钻牙轮打捞篮单根底，井底，底部重量，比重钻压双侧向测井NGT-natural gammaray spectroscopytoolLDT-litho-density toolHDT-high-resolution dipmetertoolMSFL-micro-spherically focusedlogCNL-compensatedneutron (porosity) logRFT-repeat-formationtesterWST-well sei*ic toolFin.-finishPB-plugged (plugging) backCBL-cement bond logVDL-variabledensityCCL-casing collar locator logPkr-packerDST-drill stemtesterTP-test pressureFSIP-final shut-in pressureFSIT-final shut-in timeF.L.-fetch/ loadSudd.-suddenlyPerf.-perforationReptd-reportedWoo-wait on orderPooh-pull out of hole 起钻DR-drilling钻进RM-reaming扩眼TOF-top of fish鱼顶MW mud weight泥浆密度自然伽马能谱测井岩性密度测井高分辨率地层倾角测井微球形聚焦测井补偿中子（孔隙度）测井重复式地层测试器井场地震仪结束，弄完，干完打水泥塞，回填水泥胶结测井变密度测井（ =VDC ）套管接箍地位器（测井）封隔器钻柱测试器测试压力最终关井压力最终关井时间取出/装入突然射孔，打眼，炮眼汇报，上报等指令CBU- circulate ?s?:kjuleit bottoms up循环一周MWD-mersurement while drilling随钻测量仪KSW- key seatwiper 键槽清洁器DP drill pipeHWDP- heavyweight drill pipeDC-drill collarSTB-stabilizerSMDC- short maganeticdrill collarPDM-positive displacementmotorNMDC-nonmagnetic drill collarBOP-blowout preventerCSCcasingJNT-JointXO-cross overFHfull hole