kfe管道吹扫方案

中国石油编号：安第斯石油公司厄瓜多尔有限公司燃料厂检修工程ANDES PETROLEUM ECUADOR LTD.Fuel Plant Turnaround Project工艺管道吹扫方案Pipeline Purging Procedure中国石油工程建设公司China Petroleum Engineering& Construction Corp.2013年2月February 2013授课：XXX目录Contents1、编制说明Compilation Description11.1 工程说明Engineering Description11.2 编制依据 Establishments Basis12、工程概况 Engineering Overview13、吹扫目的 Purpose for purging24、空气吹扫Air purge24.1 吹扫方法Purging method24.2 吹扫注意事项Precautions for purging35、合格标准Qualified standard4授课：XXX1、编制说明Compilation Description1.1 工程说明Engineering Description安第斯石油厄瓜多尔燃料厂检修工程共分为三个装置，分别为初馏装置、气体装置分馏装置。检修工作主要对装置的塔类设备、容器类设备、空冷器设备、换热器类设备、加热炉、工艺管道和电气仪表专业进行。Andes Petroleum Ecuador Ltd. has three fuel plants: Gas, Fractioning and Topping Plants. The maintenance service for the three plants will be included but not limited to tower, container, air cooler, and heat exchanger, heating furnace, piping and electrical & instrument works this time.1.2 编制依据 Establishments Basis 中国石油工程建设公司程序文件、质量保证手册和管理制度。 安第斯提供的图纸及相关资料。 China Petroleum Engineering Construction Company Program Files , Quality Assurance Handbook and management system. The ANDES provide drawings and related materials.2、工程概况 Engineering Overview本次检修的三套装置中，装置内运行的介质属于易燃、易爆物料，工艺管线的检修内容主要包括：安装盲板、配合业主和第三方对管线检查，部分管线更换；阀门检查，阀门更换；安全阀检查、校验；垫片更换；施工需要拆除的管线的恢复及对腐蚀和磨损严重的管线或管件更换等。管线材质涉及碳钢、不锈钢管和耐热钢管，在检测的过程中如果发现壁厚超标要及时报告业主进行处理，业主确认后同意更换该部分管线或管件后要及时向业主报材料计划。The medium operated in the three plants belongs to the materials which is easy to be inflammable and explosive. Therefore, the contents for maintenance service will be included but not limited to the following items: install blind, cooperate with client and the third party to inspect and replace the piping if necessary; inspect and replace valve if necessary; inspect and calibrate safety valve and replace the gasket; re-install the piping and replace the damaged or rusted. The materials of the pipe refer to the carbon steel, stainless steel and heat resisting pipe. Report the client for approval to handle if the thickness of pipe is found beyond the required design and also report the materials application plan to client after the approval is confirmed to replace the pipe.授课：XXX3、吹扫目的 Purpose for purging彻底吹扫出蒸汽管线内的氧化层、腐蚀产物、焊接残余物、赃物等，同时将金属表面的浮锈吹扫干净，以避免设备在运行时，浮锈及某些固体颗粒损坏汽轮机叶片，从而影响整个装置的生产。Thoroughly purged out of the oxide layer within the steam line , corrosion products, welding residue , stolen goods , etc. , while the rust of the metal surface is purged to avoid device at run time, rust and some solid particles damage the turbine blades , thereby affecting the production of the entire apparatus .4、空气吹扫Air purge4.1 吹扫方法Purging method4.1.1 利用业主提供的工厂风作为吹扫气源，如果不具备工厂风，利用空压机，增设储气罐作为吹扫气源。Factory wind as a purge gas source, dont have the factory wind , the use of air compressors, the addition of the gas tank as a purge gas source .4.1.2 管道系统水压试验的盲板不能拆除，作为吹扫系统的临时挡板。Piping system hydraulic pressure test of the blind plate couldnt tear down, as blowing system temporary damper.4.1.3 隔离不允许吹扫的设备和管道；拆除已安装的孔板、法兰连接的调节阀、重要阀门、节流阀、安全阀、仪表等，对于焊接的上述阀门和仪表，采取流经旁路或卸掉阀头及阀座加保护套等保护措施。The isolation not allowed to purge the equipment and piping ; dismantle installed orifice regulating valve flange connection , it is important valves , throttle valves , safety valves , instrumentation , etc. , for welding the valve and instrumentation , to take the flow through the bypass Remove the valve head and seat plus protective sleeve or protective measures .4.1.3 在系统内选择放空口或者排凝口作为进气口，并制作软管连接接头。Within the system to select the vent port as the intake port or an exhaust condensate , and the production of the hose connector .4.1.4 利用软管将气源和吹扫系统进气口连接，开启进气口管道系统阀门，进行吹扫。The hose inlet connection of the gas source and the purge system , opening of the piping system of the air inlet valves and purge .授课：XXX4.1.5 系统吹扫时，所有导淋、放空阀等同时吹扫，但必须在系统吹扫基本干净后，才能吹扫。System purge , all guided cream, the vent valve and simultaneously purge , but it must be in a basic clean system purge to purge .4.1.6 吹扫时应尽量将排放口错开一段间距，无法错开时应在下一管口前加铁皮挡板，并在排气口与挡板间留着一定间隙，有利于管线内杂物的排出。Purge should try to stagger the outfall some spacing the plus iron baffle before the next nozzle should not be able to stagger , and keep a certain gap between the exhaust port and the baffle , is conducive to the pipelines debris discharge .4.1.7 有副线的各调节阀应先通过付线吹扫，无付线的要拆下阀体，加装临时短管向下游吹扫。Vice lines each should pay line purge without pay line remove the valve , the installation of a temporary short tube downstream purge control valve .4.1.8 吹扫管线上的单向阀与吹扫空气的流向相反时，单向阀应调向或拆除用短节代替使气流通过，所有调向的单向阀均要登记标注并编号，吹扫结束后专人负责复位。Check valve in the purge line with a purge air flows in the opposite , the check valve should be adjusted to or removal of short section instead of the airflow through all tune to a check valve to be registered labeled and numbered , purge ends after the person responsible for reset.4.1.9 联锁阀、电动阀不能作为吹扫用阀，吹扫干净的系统可以将这类阀门投用。Interlock valve , electric valve cant be used as a purge valve，Blowing clean inside the system of this kind of valve can be the revamping.4.2 吹扫注意事项Precautions for purging4.2.1 吹扫管线上安装的所有过滤器、止回阀、流量计、孔板、调节阀等需要拆除，用短管连接。Installed on the purge line filter , check valves, flow meters , orifice , regulating valve need to be removed , with the short tube connection .4.2.2 所有仪表线的引压阀、压力表手阀、液位计连通阀以及采样阀等需要关闭。在系统吹扫基本干净后，才对吹扫仪表引压管、导淋、放空阀等进行吹扫。All instrument impulse line valves , pressure gauges hand valve , the level gauge connectivity valve and sampling valve needs to close. In basic clean system purge , fishes purge meter cited pressure pipe guide shower vent valve , purge .4.2.3 吹扫口的开口距离在5cm以上，吹扫时，必须注意安全，排放口要设立明显的标志，并有专人监护，以防伤人。授课：XXXPurge mouth opening distance of more than 5cm , purge , must pay attention to security , outfall to establish obvious sign , and to supervise , to prevent injury .4.2.4 检验管道支吊架的牢固程度，必要时应予以加固。 The test pipe supports and hangers as strong , if necessary, should be reinforced .4.2.5在吹扫安全阀时，应在与管道连接处的法兰断开并加挡板保护阀口，吹扫气体从档板前排放。In the safety valve of the purge should be disconnected in connection with the pipe at the flange plus baffle protection valve port, the purge gas is discharged from the baffle before .4.2.6 要遵循先少量给空气贯通、排水，再提量空气吹扫的原则：首次给空气吹扫或突然提空气量时，在排放口要有专人监护，以免吹出杂物刺伤人员。排放口最好用物品挡住，以免脏物飞溅。To follow a small amount through the air , drainage, mention the amount of the air purge principle : the to purge or sudden mention of the amount of air to the air for the first time , in the discharge port to have someone care to avoid blowing debris stabbed . The outfall is best blocked by other objects to prevent dirt splashing .4.2.7 空气进设备必须缓慢，要有一个缓慢的升压过程，以防突然升压而导致系统空气压力波动。Slow air into the device must have a slow step-up process , to prevent a sudden boost system air pressure fluctuations .4.2.8 吹扫时，注意安全，防止铁屑吹入眼睛，空气引入装置后，凡需进入的容器设备管道必须事先进行确认方可进入。Purge , attention to safety, to prevent the iron filings blown into the eyes , If students enter the container air after the introduction of the device , the device pipeline must be confirmed before entering .4.2.9 空气吹扫时，宜进行间断性吹扫，空气流速不得不于20 m/s。Air purge should be carried out intermittent purge air flow rate had to 20 m / s .5、合格标准Qualified standard在排出口用白布作为靶板检查，在5分钟内靶板上无铁锈及其他杂物为合格或通过观察凝液的透明度，无铁锈为合格。Check the discharge port with a white cloth as Target Target no rust and other debris within 5 minutes as qualified or through the transparency of the observation of condensate , no rust is qualified . （注：可编辑下载，若有不当之处，请指正，谢谢!） 授课：XXX