手机结构2D图技术标注参考规范Word编辑

传播优秀Word版文档 ，希望对您有帮助，可双击去除！德信无限通讯科技(上海)有限公司TechFaith Wireless Communication Technology (Shanghai) Co.,LTD.结构2D图 技术标注参考规范文件编号 ：QC1001保密等级 ：保密文件类型 ：管理办法有效期 ：3年页数 ：1/1版本 : 1.0编制日期 ：2004/05/24开始执行日：2005/07/01NO编制/变更日期变更理由变更内容版本编制/修改人批准12004/05/24新编0.1沈林王迅22006/01/04修改将2D标准样板图中技术标注更新到本文件中1.0蒋伟鹏丁勇传播优秀Word版文档 ，希望对您有帮助，可双击去除！目录索引01. Latch02. Antenna03.1 PCBA limited drawing03.2 PCBA outline drawing04. Battery 05.1 Lens(注塑)05.2 Lens(CNC)06.1 Audio cover06.2 RF_switch_cover07.1 Shielding cover07.2 Shielding frame 07.3 Spring08. Metal dome09. Stop TPU10. Light guide 11. Fpcba12.1 金属装饰件12.2 Logo12.3 Plating plastic12.4 Electroform13.1 双面胶13.2 泡棉传播优秀Word版文档 ，希望对您有帮助，可双击去除！13.3 铜箔13.4 绝缘片14.1 Keypad asm14.2 keypad rubber14.3 Keypad 电镀键帽14.4 Keypad 数字键15.1 外观漆喷漆图15.2 导电漆喷漆图16. Housing part drawing17. Housing Assembly18. Explode传播优秀Word版文档 ，希望对您有帮助，可双击去除！01. Latch技术要求（Notes）:1. 材料：POM Dupont500, 用100%原材料; Material: POM Dupont500,use 100% raw material .2. 尺寸: 图面尺寸用于检验零件外形、功能和装配; 未注圆角R0.05,未注脱模斜度1度, 未注尺寸依照Pro/e 3D Data; 标有环形圈:每批次出货均需检查；Qualify时需要做CP/CPK; Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly; Unspecified round: R0.05mm; Unspecified draft angle: 1%d; Unspecified dimensions refer to Pro/e 3D model data; Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.3. 公差：未注公差依照图面公差表; Tolerance: Unspecified tolerance should comply with tolerance table in the drawing;4. 外观：成品清洁、无杂质、无划伤、缩水及其它瑕疵; 飞边及分型线段差0.03mm;顶杆痕0.05mm;浇口凸出0.10mm; 穴号应刻在模具上，标志不得高于表面; 外观皮纹: VDI 24; Appearance：Product should be tidy and purity, no nick, no shrinkage and other blemish; Galling should be less than 0.03mm; Ejector rod mark should be less than 0.05mm; gate trim should be less than 0.10mm; Cavity number shall be located low on the surface. Appearance require:VDI 24.5. 检测须满足德信质量标准:部品检验标准_注塑件_x.x_xxxxxx Product should be satisfied with quality standard of Techfaith Wireless:部品检验标准_注塑件_x.x_xxxxxx02. Antenna1.材料：见图,用100%原材料;1.Material: Refer to the drawing table, in original color and with 100% raw material.2.尺寸：图面尺寸用于检验零件外形、功能和装配; 未注圆角R0.05,未注脱模斜度1度, 未注尺寸依照Pro/e 3D Data; 标有环形圈的是重点尺寸,每批次出货均需检查,Qualify时需要做CP/CPK；2.Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly;返回索引目录 Unspecified round: R0.05mm; Unspecified draft angle: 1; Unspecified dimensions refer to Pro/e 3D model data; Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.传播优秀Word版文档 ，希望对您有帮助，可双击去除！3.公差：未注公差依照图面公差表;3. Tolerance: Unspecified tolerance should comply with tolerance table in the drawing;4.外观: 成品清洁、无杂质、无划伤、缩水及其它瑕疵;飞边及分型线段差0.03mm,顶杆痕0.05mm;浇口凸出0.05mm;穴号应刻在模具上，标志不得高于表面;外观皮纹：抛光4.Appearance：Product should be tidy and purity, no nick, no shrinkage and other blemish;Galling shall be less than 0.03mm, ejector rod mark shall be less than 0.05mm, gate trim shall be less than 0.05mm.Cavity number shall be located low on the surface. Surface shall be smooth.5.电气性能依照规格书：violet1-Antenna SPEA-05-02-18.pdf。5.Electro performance shall be according to spec: violet1-Antenna SPEA-05-02-18.pdf6.喷涂: 范围:见喷漆图； 油漆颜色及色差:E1； 喷漆厚度: 底漆8-10 um；UV10-12 um； 油漆硬度:2H，500gf； 油漆耐磨:RCA 300 cycles； 油漆附着力:百格实验，脱落面积3%.6.Coating:Painting range:refer to the painting drawing.Paint color and aberration: E1 Paint thickness:BC 8-10 um；UV10-12 um；Paint hardness test: 2H，500gfPaint abrasion test: RCA 300 cyclesPaint peeling test: area of peeling3%.7.包装与运输:零件独立包装,放入托盘对应的凹穴,托盘层堆放入纸箱;7.Package and Transport: Product should be packaged independent, and lay in tray, finally put the trays in the paper box;8.检测须满足德信质量标准： 部品检验标准-天线VX.X8.Product should be satisfied with quality standard of Techfaith Wireless: 部品检验标准-天线VX.X.03.1 PCBA Limited drawing 1. 区域限高为电子元件限高，不包括SHIELDING和图中已经标出的结构电子件。返回索引目录 (Shielding) -指可以放置屏蔽罩区域。放置屏蔽罩时，罩内元件限高； (No Shielding)-指可以放置屏蔽罩区域。不放置屏蔽罩时元件限高； Limiting Height for shielding area is only for electronic componets inside , not including shielding and the mechanical electronic components been included in this drawing; (Shielding) -Shielding is allowable is this area.The limiting height for the components with shielding； (No Shielding)-Shielding is allowable is this area.The limiting height for the components without shielding传播优秀Word版文档 ，希望对您有帮助，可双击去除！；2. 器件准确位置以文件中的 直角顶点为准;IO ConnAudio jack etc.位置以PCB定位孔为准; The vertex of the right-angle indicate the center of the componets . Location of IO Conn /Audio jack etc. base on the PCB orientation holes;3. 器件布置时元件PAD 不能超出限高区域边界线; Componentspad should be located inside the the outline of limited area;4. 螺丝孔做(不做)铜化处理。 Screw hole is PTH（NPTH） type.03.2 PCBA outline drawing1. 图面尺寸用于检验PCB外形、功能和装配; Specified dimensions in the drawing are used to check PCB outside shape, function and assembly;2. 重点尺寸:标有环形圈，每批次出货均需检查；Qualify时需要做CP/CPK； Specified dimensions with marked ring are critical dimensions, need to be checked every shipment; and must do CP/CPK check in the Qualification stage;3. 未注公差参照图面公差表; Unspecified tolerance should comply with tolerance table in the drawing;4. 产品检验标准：PCB来料外观检验标准1.0_050412； Product should be satisfied with quality standard of Techfaith Wireless: PCB来料外观检验标准1.0_050412；5.包装： 产品按一定数量密封包装，需防污防潮。 Package of product should be quantitative, sealed, dustless and dampproof .04. BATTERY1.电池后盖与电芯之间用双面胶粘贴;Using double adhesive between battery rear cover and cell;2.电池前后盖超焊后，前后壳配合周边严禁溢料;返回索引目录 焊接牢固可靠，不许有虚焊，封装后厚度方向的变形量不超过0.15mm;After ultrasonic welt,burr is forbidden around battery;The welding should be fastness and dependable, no false-welding,deformation in heignt should be less than 0.15mm.3.尺寸: 图面尺寸用于检验零件外形、功能和装配; 标有环形圈的是重点尺寸,每批次出货均需检查；Qualify时需要做CP/CPK;Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly; Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.4.BATT_CONN需镀金，镀层厚度不小于0.5um; Batt_conn must be gilt, coating thickness must be no less than 0.5um传播优秀Word版文档 ，希望对您有帮助，可双击去除！ 盐雾试验：35，5% 氯化钠溶液，48小时后无腐蚀; Salt fog test: In35C 48h 5% NaCl salt fog concentration, it can not be rusty after 48hs 跌落试验：1.5米高度，6面3棱1角分别跌落，水泥地面， 两轮共20次跌落，电池功能正常，外观无明显损伤;1.5m drop test: 6 faces (Left Back Right Bottom Top Front) , 3 edges 1corner ,1 drop per face,edge ;corner,2cycles, battery function must be normal , have no obvious damages in apperance.5.电气性能依照文件：Li+电池SPECVX.X; Electric function refer to: Li+BATTERY SPECVX.X6.包装与运输：电池用塑料袋和纸盒独立包装。 Package and Transport: Product should be packaged independent, and lay in tray, finally put the trays in the paper box;7.检测须满足德信质量标准： Product should be satisfied with quality standard of Techfaith Wireless: 部品检验标准_注塑件V X.X ;GB_T18287_2000蜂窝电话用锂离子电池总规范05.1. LENS(注塑) 技术要求：1. 图面尺寸用于检验零件外形、功能和装配， 未注尺寸请参考3D Pro/Engineer 零件图。 Specified dimensions in the drawing are used to check outside shape, function and assembly;Unspecified dimensions refer to Pro/e 3D model data;2. 重点尺寸:标有环形圈。每批次出货均需检查；Qualify时需要做CP/CPK；Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.返回索引目录3.未注公差参照图面公差表;Unspecified dimension tolerance should comply with the general tolerance table in drawing.4. 材料： 材料采用 PMMA 三菱VRL-40 ,颜色为无色透明,注塑时须采用100%原材料。 Material: PMMA VRL-40(Mutusubishi), transparent color and with 100% virgin material.5. 外观： Appearance: 1)所有圆角半径和脱模斜度按照Pro/e 3D Data; Round and draft should comply with Pro/e 3D Data 2)未注脱模斜度为1度,未注圆角为R0.2; Draft angle should be less than 1%d, unless otherwise specified. Unspecified round: R0.2mm; 3)浇口切割后,残留0.05mm. GATE PROJECTION SHALL NOT EXCEED 0.05MM BEYOND THE PART SURFACE UNLESS OTHERWISE SPECIFIED. 4)LENS透明部分要求在黑色背景检查,要求表面无变形,无黑白点及其它瑕疵; LENS transparent area should be checked in black background, no flaws. 5)印刷部分要求色彩均匀、无划伤、黑白点、瑕疵;传播优秀Word版文档 ，希望对您有帮助，可双击去除！ Print area shoudle be uniformity, no nick , no flaws. 6)印刷字体及颜色请参照右下脚表; Artwork should be in the file index in the right-down corner.6、透光率91%以上; Transparency ratio: 91%.7、正面喷涂UV,UV漆表面硬度3H,1kgf Hardness of surface should be more than 3H,1kgf after UV coating.8. 耐磨:RCA 300 cycles； Wearable : RCA 300 cycles；9. 附着力:百格实验，脱落面积3%，并没有整格脱落； The ply adhesion of printing ink : 3% ,no hwale pane desquamate.10. 模具要求： Tooling requirement: 产品区域无顶杆痕. No mark of injection pin. 浇口位置需与设计者商定； Locations of gate should be determined by arrangements. 外观为镜面; Texture: polished to mirror .11、环境要求：产品应在十万级以上工作室清洁、包装. Environment requirement: Product should be made and packaged in clean condition.12. 包装与运输： 零件需独立包装，产品两表面需有静电保护膜， 放入托盘对应的凹穴，托盘层堆放入纸箱。 Package and Transport: Product should be packaged independent, and lay in tray, 返回索引目录 finally put the trays in the paper box; surface of product should be protected with static film. 13、检测须满足德信质量标准： Product should be satisfied with quality standard of Techfaith Wireless: 1)部品检验标准-Lens_VX.X_XXXXX.pdf 2)手机综合检验标准_VX.X_XXXXXX.pdf 05.2. LENS(CNC)1. 图面尺寸用于检验零件外形、功能和装配， 未注尺寸请参考3D Pro/Engineer 零件图。 Specified dimensions in the drawing are used to check outside shape, function and assembly; Unspecified dimensions refer to Pro/e 3D model data; 2. 重点尺寸:标有环形圈。每批次出货均需检查；Qualify时需要做CP/CPK； Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.3.未注公差参照图面公差表;传播优秀Word版文档 ，希望对您有帮助，可双击去除！ Unspecified dimension tolerance should comply with the general tolerance table in drawing.4. 材料：材料采用 PMMA 三菱NR200板材 ,颜色为无色透明。 Material: PMMA NR200(Mutusubishi), transparent .5. 外观： Appearance: 1)LENS透明部分要求在黑色背景检查,要求表面无变形,无黑白点及其它瑕疵; LENS transparent area should be checked in black background, no flaws. 2)印刷部分要求色彩均匀、无划伤、黑白点、瑕疵; Print area shoudle be uniformity, no nick , no flaws. 3)印刷字体及颜色请参照右下脚表; Artwork should be in the file index in the right-down corner.6. 透光率93%以上. Transparency ratio: 93% 7、表面硬度5H,1Kgf; Hardness of surface should be more than 5H,1kgf.8. 耐磨:RCA 300 cycles； Wearable : RCA 300 cycles；9. 附着力:百格实验，脱落面积3%，并没有整格脱落; The ply adhesion of printing ink : 3% ,no hwale pane desquamate.10、环境要求：产品应在十万级以上工作室清洁、包装. Environment requirement: Product should be made and packaged in clean condition.11. 包装与运输：返回索引目录 零件需独立包装，产品两表面需有静电保护膜， 放入托盘对应的凹穴，托盘层堆放入纸箱。 Package and Transport: Product should be packaged independent, and lay in tray, finally put the trays in the paper box; 12、检测须满足德信质量标准： Product should be satisfied with quality standard of Techfaith Wireless: 1)部品检验标准-Lens_VX.X_XXXXX.pdf 2)手机综合检验标准_VX.X_XXXXXX.pdf06. Audio_cover & RF_switch_cover06.1. Audio_cover1.材料：SANTOPRENE 201-64，硬度：643SHA，用100%原材料; Material: SANTOPRENE 201-64, hardness: 643 SHA,with 100% raw material .2.尺寸: 图面尺寸用于检验零件外形、功能和装配; 未注尺寸依照Pro/e 3D Data，未注圆角R0.05,未注脱模斜度1度; 标有环形圈的是重点尺寸,每批次出货均需检查,Qualify时需要做CP/CPK;Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly; Unspecified round: R0.1mm; Unspecified draft angle: 1degree; Unspecified dimensions refer to Pro/e 3D model data;传播优秀Word版文档 ，希望对您有帮助，可双击去除！ Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the qualification stage.3.公差：未注公差依照图面公差表; Tolerance:Unspecified tolerance should comply with tolerance table in the drawing;4.外观：边及分型线段差0.05mm; 成品清洁、无杂质、无划伤、缩水及其它瑕疵; 顶杆痕低于表面00.05mm;浇口凸出0.05mm; 穴号应刻在模具上，标志不得高于表面; 外观皮纹: VDI 21; Appearance:The burr , step of part-line : 0.05mm Product should be tidy and purity, no nick, no shrinkage and other blemish; Mark of ejection pin should be lower 0.05mm than product surface; Height of injection gate remained in the product should be lower 0.05mm; Cavity number should be carved on cavity or core,Its mark no higher than product surface. Surface texture: VDI 21;返回索引目录5. 包装与运输：采用夹链袋包装，注明袋内数量; Package and Transport: packaged by chain bags,and label the quantity .06.2. RF_switch_cover1. 图面尺寸用于检验零件外形、功能和装配，未注尺寸请参考3D Pro/Engineer 零件图。 Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly; Unspecified dimensions refer to Pro/e 3D model data;2. 材料:采用silicon rubber;硬度要求：6070SH A Material: silicon rubber;Hardness：6070SH A3. 公差/外观：未注公差参照图面公差表； Tolerance: Unspecified tolerance should comply with tolerance table in the drawing; 飞边及分型线段差不得大于0.1mm， 所有圆角半径和脱模斜度按照Pro/e 3D Data； Step of parting_line should be less than 0.1mm unless otherwise specified， All Radius of corner and draft angle should be Pro/e 3D Data； 完成产品应清洁、无杂质，零件外表面应光滑,无飞边、无划伤、缩水及其它瑕疵； Product should be tidy and purity, suface shoud be smooth, no nick, no shrinkage and other blemish; 重点尺寸:标有环形圈; Specified dimensions with marked ring are critical dimensions 成型颜色要求：采用PANTONE cool gray 4c Color of molding:use PANTONE cool gray 4c4. 包装与运输：采用夹链袋包装，注明袋内数量。 Package and Transport: package by chain bags and lable the quantity. 传播优秀Word版文档 ，希望对您有帮助，可双击去除！07. Shielding、spring07.1. Shielding_cover1.材料: SUS304(不锈钢),T=0.20mm; 1.Material: SUS304(stainless steel), T=0.20mm,; 2.尺寸:图面尺寸用于检验零件外形、功能和装配;未注尺寸依照Pro/e 3D Data; 标有环形圈的是重点尺寸,每批次出货均需检查,Qualify时需要做CP/CPK;2.Dimension: specified dimension in the drawing shall be used to check outside shape,function and assembly; unspecified dimensions refer to Pro/e 3D model data;返回索引目录 Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.3.公差:未注公差依照图面公差表;3.tolerance: Unspecified tolerance should comply with tolerance table in the drawing;4.外观:毛刺0.05mm, 为冲切毛刺方向，成品清洁、无杂质、无划伤及其它瑕疵; 无凹陷，凸起，平面度0.1mm;4.Appearance: stamping burr shall be less than 0.05mm, the symbol indicates burr direction; finished product be tidy, no purity, no scratch, no sink depressions, no heave and other defects. the planeness shall be less than 0.1mm;5.包装与运输：零件独立包装，放入托盘对应的凹穴，托盘层堆进纸箱。5.package and transportation: Product should be packaged independent, and lay in tray, finally put the trays in the paper box;6.检测须满足德信质量标准：金属件检测标准VX.X6.Product should be satisfied with quality standard of Techfaith Wireless: 金属件检测标准VX.X07.2. Shielding_frame1.材料:C7521R(镍白铜),T=0.20mm,保证良好焊接性能，任何两点间电阻不大于0.2欧姆;1.Material: C7521(cupronickel),the material have the well performance of welding , any two points resistance shall be less than 0.2;2.尺寸:图面尺寸用于检验零件外形、功能和装配;未注尺寸依照Pro/e 3D Data;标有环形圈的是重点尺寸,每批次出货均需检查,Qualify时需要做CP/CPK;2.Dimension: specified dimension in the drawing shall be used to check outside shape,function and assembly; unspecified dimensions refer to Pro/e 3D model data; Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.传播优秀Word版文档 ，希望对您有帮助，可双击去除！3.公差:未注公差依照图面公差表;3.tolerance: Unspecified tolerance should comply with tolerance table in the drawing;4.外观:毛刺0.05mm, 为冲切毛刺方向，成品清洁、无杂质、无划伤及其它瑕疵; 无凹陷，凸起，平面度0.1mm;4.Appearance: stamping burr shall be less than 0.05mm, the symbol indicates burr direction; finished product be tidy, no purity, no scratch, no sink depressions, no heave and other defects. the planeness shall be less than 0.1mm;5.包装与运输： 把屏蔽罩同向放入SMT编带包装，运输途中避免受压变形。5.package and transportation: put shieling in SMT band ,Dont change the figure with press返回索引目录 in transport.6.检测须满足德信质量标准：金属件检测标准VX.X6.Product should be satisfied with quality standard of Techfaith Wireless: 金属件检测标准VX.X07.3. Spring技术要求:1.弹簧预压缩1.50mm，最大压缩3.30mm；1.Pre-compresss spring is 1.5mm, the largest compress is 3.3mm.2.弹簧参数：见参数表；2.parameter of spring: see the table of parameter;3.F/S图：见图；3.The drawing of F/S: see this F/S drawing; 4.材料：SUS304；4.Material:SUS304(stainless steel); 5.包装与运输：采用自封袋包装，标明数量。5.package and transportation: Product should be lay in self-given sack, and mark the quantity;6.检测须满足德信质量标准：金属件检测标准VX.X6.Product should be satisfied with quality standard of Techfaith Wireless: 金属件检测标准VX.X08. Metal_dome1、图面尺寸用于检验零件外形、功能和装配； Specified dimensions in the drawing are used to check outside shape, function and assembly;2、重点尺寸:标有环形圈。每批次出货均需检查；Qualify时需要做CP/CPK； Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage; 传播优秀Word版文档 ，希望对您有帮助，可双击去除！3、公差：未注公差依照图面公差表; Tolerance: Unspecified tolerance should comply with tolerance table in the drawing4、产品采用气槽结构; Exhaust mode:Ventilated groove; 5、Metaldome 5(2.0测试头)，材料：SUS301返回索引目录 弹力OF:180+/-30g 手感C.R:45%15 4(1.5测试头)，材料：SUS301 弹力OF:160+/-30g 手感C.R:45%15 Metaldome 5(2.0 test surface)，material：SUS301 operation force OF:180+/-30g click ratio C.R:45%15 4(1.5 test surface)，material：SUS301 operation force OF:160+/-30g click ratio C.R:45%156、EMI层采用网状印刷,接地点弯折后最远两点间电阻1. The EMI layer is printed reticulation,the insulation resistance of the two farthest points is1 after bending;7、外型及DOME位置公差为:0.1mm; The tolerances of the outline and the domes location: 0.1mm;8、产品附于离形纸上。需防尘、防潮。 The products stick on the glassine paper.Need dustproof and dampproof.09. STOP_TPU1.材料：SANTOPRENE 201-64，硬度：643SHA，用100%原材料; Material: SANTOPRENE 201-64, hardness: 643 SHA,with 100% raw material .2.尺寸: 图面尺寸用于检验零件外形、功能和装配; 未注尺寸依照Pro/e 3D Data，未注圆角R0.05,未注脱模斜度1度; 标有环形圈的是重点尺寸,每批次出货均需检查,Qualify时需要做CP/CPK;Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly; Unspecified round: R0.1mm; Unspecified draft angle: 1degree; Unspecified dimensions refe