资源描述
Available protocols (incomplete and expanding)NO.编号Protocol协议Sub_protocol子协议RF Chip射频芯片1FLYSKYFLYSKY V9X9 V6X6 V912 CX20A71052AFHDS2APWM PPM IBUS SBUSA71053HUBSANNONEA71054FRSKYVNONECC25005FRSKYDNONECC25006FRSKYXCH_8 CH_16 EU_8 EU_16CC25007S-FHSSNONECC25008DSMDSM2_11DSM2_22 DSMX_11 DSMX_22CYRF69369DEVONONECYRF693610WK2X01WK2801WK2401CYRF693611J6PRONONECYRF693612ESKYNONENRF24L01 +13HISKYHISKY HK310NRF24L01 +14KNWLTOYS FEILUNNRF24L01 +15V2X2V2X2 JXD506NRF24L01 +16ASSANNONENRF24L01 +17MJXQWLH08 X600 X800 H26D E010 H26WHNRF24L01 +18YD717YD717 SKYWLKR SYMAX4 XINXUN NIHUINRF24L01 +19SYMAXSYMAX SYMAX5CNRF24L01 +20SLTSLT VISTANRF24L01 +21CX10GREEN BLUE DM007 JC3015 MK33041NRF24L01 +22CG023CG023 YD829 H8 3DNRF24L01 +23BAYANGBAYANG H8S3DNRF24L01 +24MT99XXMT99 H7 YZ LS FY805NRF24L01 +25SHENQINONENRF24L01 +26FY326FY326 FY319NRF24L01 +27FQ777NONENRF24L01 +28HONTAIHONTAI JJRCX1 X5C1 FQ777 951NRF24L01 +29Q2X2Q222 Q242 Q282NRF24L01 +30Q303Q303 CX35 CX10D CX10WDNRF24L01+131GW008NONENRF24L01 +32DM002NONENRF24L01 +33ESKY150NONENRF24L01 +34CORONACOR V1 COR V2 FD V3CC2500Operating current: =180mARF power: +22dBmWeight: 32gParameters：Operating voltage:5-9VOperating frequency: 2.4G ISM bandMCU: STM32F103CBT6(128K ROM, 20K RAM)Introduction:This 4-in-1 TX module is suitable for FRSKY X-Lite. It integrates four RF chips (CC2500,NRF24L01+,A7105,CYRF6936) into one single circuit board, it supports a variety of remote control protocols, such as Futaba S-FHSS, Walkera DEVO, Spektrum DSM2, DSMX, Flysky, Frsky, WLToys, Hubsan, Hisky, Esky , Assan etc.You can control your model flexibility with it, and you will get much excellent experience with you favorite transmitter.This module is compatible with the Multi-module project on github. Its based onserial mode. In thisSTM32 microcontroller. All available protocols are included in mode, it uses a serial protocol to communicate with your transmitter. The serial protocol does not require any hardware modifications, but you should update the firmware on your transmitter to the latest. Then the model protocol selection and binding is done from the Model Settings menu on your transmitter. For telemetry capable transmitters, the telemetry integration is done seamlessly with the transmitter firmware.For more information, please scan the QR code to access :How to use:1. Refer to the website above, update your transmitter with proper firmware.2. Screw down the antenna of module tightly, and then install TX Module to the module bay of your transmitter.3. Power on your transmitter, enter Model Settings menu, turn on External RF , and select MULT mode, then you will see the bind and protocol button in the menu, and then you can choose a proper protocol for you model and bind with it now.LED State:Green LedRed LedStatusOFFFlashing raipidlyBootloader is running, please waitONONNormal or Range CheckONFlashing slowlyNo serial inputONFlashing raipidlyBindingNotice:1. Make sure to check the multimodule option, when you update OpenTX firmware through Companion software.2. In serial mode, for FRSKY and S-FHSS protocol, you may need set the value of Fine or Option (in Model Settings menu on your TX) properly to bind with your model. The value can be varied, since it partly depended on your model.
展开阅读全文