gp2000摩托罗拉对讲机说明书

,单击此处编辑母版标题样式,2012/6/1,#,单击此处编辑母版文本样式,第二级,第三级,第四级,第五级,Motorola gp2009 manual,摩托罗拉,gp2009,说明书,Installation and removal of,antenna,安装,和拆卸天线,1. The,bottom of the thread of,the,antenna into the antenna coupling, antennaFasten to the transceiver,.,将天线的螺纹底部放入天线联接器中，将天线,扣紧到对讲机中,。,2.,Clockwise until,tighten,以顺时针方向旋转直到拧紧,拆卸,Until it is disengaged from the,walkie-talkie,on the counter-clockwise rotating antennaDetachment,.,以逆时针方向旋转天线直到它从对讲机上脱开,拆离,Installation and removal of the,battery,安装和拆卸电池,Installing the,battery,安装,电池,1.A,slot of the battery,into,the notch of the walkie-talkie,.,将电池的槽放入对讲机的槽口中,2 slide-phone battery,until,you hear a click sound,.,向上滑动对讲机电池直到听到“咔哒”声,Removing the,Battery,拆卸电池,1,battery card allocated from the,transceiver,将,电池卡从对讲机上拨,出,Slide,the battery,down,2.,向下,滑动电池,Installation and removal of the belt,clip,安装,和拆卸皮带夹,Install the belt,clip,安装皮带,夹,1.Adjust,the belt clip slot at,the,Installation,on the walkie-talkie batteryTrack,.,调整,皮带夹的卡槽对准对,讲,机,电池上的,安装轨。,2.Slide,down the belt clip,until,you hear a clicking sound,.,2.,向下滑动皮带夹直到听见“咔哒”声,Removing the belt,clip,拆卸皮带,夹,In the demolition button and walkie-talkie back of the battery between the end of,the,key inserted. Up the proposed demolition button. Slide the belt,.,在拆卸掣和对讲机电池背面之间将钥匙的末端,插入。 向上,提出拆卸,掣。向上,滑动皮带。,Charge for,walkie-talkie,为对讲机充电,1.A,turn off the intercom and to the chargers DC power supply,.,(Such as walkie-talkie and electricalSources are open),2.,the transceiver into the charger socket.,3.Open,the DC power charger.,4.Open,the DC power supply.5 walkie-talkie charge until the charger,LED,indicator lights up in green(About two hours later).,6.Open,walkie-talkie, when charging is completed,you,will see the battery indicator,Displays,three power bar.,1.,关闭对讲机和到充电器的直流电源。（如对讲机和电,源都开着,）,2,.,将对讲机置入充电器插座。,3.,打开充电器的直流电源,。,4,.,打开直流电源,。,5,.,对对讲机充电直到充电器的,LED,指示灯亮起绿色,灯（,大约两小时之后）,。,6,.,打开对讲机，当充电完成时，您会看到电池电量指示,器显示,3,个电量指示条。,Programming port and mode,of,编程端口及模式,Programming modeThis mode allows you to enhance the use of walkie-talkie function by changing the,characteristic,parameters of the,walkie-talkie. Enter,the programming modeIf the transceiver is turned on, shut down. Then press and hold the listener the key to,power,. Hear a tone after you in the walkie-talkieProgramming mode. K indicator lights up, then displays the,RW, Exit,the programming,Mode.,Shutdown,exit the programming,mode.,编程模式,这种模式允许您通过改变对讲机的特征参数来增强对讲机的使用功能。,进入编程模式,如果对讲机是开启着，请关机。然后按住监听键开机。听到一声音调之后,，,表示,您的对讲机,处在编程,模式。,K,指示器亮起，然后显示,RW,。,Scan and priority,scan,扫描和优先扫描,Scan There are two types: normal scan and priority,scan. Ordinary,scanning continuous,retrieve,the walkie-talkie channel in the scan list, priority scan 50% of the scan time,assigned,to the priority,channel(A,channel in the selected scan list,),扫描有两种类型：普通扫描和优先扫描。,普通扫描连续检索对讲机扫描列表中的所有信道，而优先扫描将,50%,的扫描时间分配,到,优先信道,(,在被选定的扫描列表中的第一个信道,),Preset programming,functions,预置编程功能,Button,type,按键类型,A key,A,键,B key,B,键,C key,C,键,D key,D,键,Short-term,keys,短时间按键,Power Selection,功率选择,Squelch level,静噪级别,PL / DPL to start,PL/DPL,启动,Scanning,扫描,Long keys,长时间按键,PTT ID starts,PTT ID,启动,Phone mode,电话模式,The keypad lock,键盘锁定,Spurious letter Tao delete,杂散信道删除,Dial,拨号,A telephone conversationAfter the call is connected, the way of normal use of walkie-talkie call.,Speech, press the PTT key, release the PTT key to answerSend a voice call,1.,Press and hold the PTT key.,2.Dial,the required selective call ID.,3.Release,the PTT key.,电话交谈,在电话接通后，以平常使用对讲机时的方式通话,。,按下,PTT,键讲话，释放,PTT,键接听,发送语音呼叫,1.,按住,PTT,键。,2.,拨打所需的选呼识别码。,3.,释放,PTT,键。,Thanks for reading,!,谢谢观看,！,