环氧云母氧化铁涂料快干型

环氧树脂云母氧化铁（快干型）漆为暴露户外的钢材提供保护，良好的防锈能力，低温下固化复涂时间短，不受复涂时间限制Intended Uses 复涂广泛的高性能面漆。用途Provide protection for steel exposed outdoor, Good corrosion resistance, Curing at low temperatureShort overcoating, diterval ont limited by time. Overcoat widely with high performance finish.Product二罐装，高膜厚环氧树脂涂料，含云母氧化铁，固化温度低至5C。Information Two packages,High build epoxdy resin paint,containing micaceous iron oxide,curing temperature 产品简介low to 5C.volume Solids 固体份70%Application Dry Flm Thickness 干膜厚度100 microns equivalent tol43 microns of wet film100微米相当于143微米湿膜厚details产品数据Theoretical Coverage理论涂布率4.2 m2/Kg at the stipulated volume solids and 100microns of dry film thickness4.2平方米/公斤,以规定体积固体份和100微米干膜厚计Practical Coverage 实际涂布率Allow appropriate loss允许适量损耗Mix Radio混合比A : B=6:l(by weight)甲：乙=6:1Method of Application 施工方法Airless Spray无空气喷涂 Recommended推荐采用BrushorRoller涂刷或辊涂 Suitable for small area.Recoatingshoulcondu for many times in order to recach the requ thickness仅适用小面积，需重复涂刷，以达到所需膜厚Storageand Handling施工详述Thinner稀释剂Not necessary in normal, if need, 正常不需要，如需要可适用C003use C003Cleaner油漆设备清洗剂C003Pot Life使用期5C:6h23C:2.5hStorage贮存期One year一年传统喷涂 Not adop table不适用Conwentional SprayDrying time 干燥时间SubstrateTemperature 底材温度Touch Dry 表干 (min)Hard Dry硬干(h)Over coating Interval 覆涂间隔Min最短Max最长5C3044hours小时23 C2022hours小时14days 天35 C2011hours小时Storage 贮存Pack size包装规格A;24Kg in 20 liter containerR4Kg in 4 liter container甲：24公斤装于20公升容器中 乙：4公斤装于4公升容器中Flash Point闪点三 23C高于23 CStorageandHandling 贮存与管理Store in cool and dry conditions 贮存于阴凉干燥处Specific Gravity 比重Approx 1.66Kg/L大约 1.66 公斤/公升Specification and技术要求及表ra处理This product is designed for the surface blasted to Sa2.5 Swedish SIS055900 or precoated with primer. Consult our company on details.The surface to be coated must be clean and dry.Blast clean to Swedish standard SIS055900 Sa2.5, Try to smooth, fill or properly treat the surface blemishes come from blasting.Surface precoated with:The surface to be coated should be clean, dry and free from dirt. Clean and remove grease to SSPC-SP1 by solvent cleaning, remove the accumulated dirt with hand bristle brush, rinse the soluble salt with fresh water. Electrowelding jioint or damaged part should be treated to the specified standard, and repaired with primer prior to painting this system. If there is serious and wide damage part on the surface, completely sanding must be conducted.The surface precoated with zinc powder with: Ensure that zinc silicate has cured prior to overcoating. The surface should be free of zinc salt. Zinc silicate primer small be applied. With the transition coat together.本产品设计用于喷砂处理至Sa2.5瑞典标准SIS055900的表面涂装，以及预涂底漆的表面涂装， 详细情况请洽询，涂布的表面必须清洁干燥。喷砂处理达瑞典标准SIS055900的Sa2.5要求，喷砂处理引起的表面瑕疵，需设法磨平，填补 或适当处理。预涂底漆表面：复涂表面必须清洁干燥、无污物、根据SSPC-SP1用溶剂清洗去除油脂，用硬刷去除积累的污 物，用清水冲去可溶性盐份,，电焊接缝或损伤部分要处置至规定的标准，并在涂装本系列产品 前用底漆修补，如表面已有严重散布的损伤，则需全面扫砂。锌份前确保硅酸锌已固化，表面必须无锌盐，硅酸锌底漆应与过度涂层一起涂装Curing time should prolong below 0C. Take care of the surface free from ice when the curing temperature approaches to ice point.The recoatbility of this product may be reduced owing to excessive painting.0C以下时，固化时间或许会延长，小心其固化温度接近冰点，其表面应无冰存在，过量涂装会 降低产品的再涂性。This product should be used in painting area by perfessional operators. When painting , please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.This product is a kind of solvent-based paint .Inorder to avoid danger or accident, minimal safety precautions,as follow , should be down .SafetyPrecautionsThe paint contains volatile solvent and is flammable . So must keep away from sparks and open flames.No smoking at applacation site ,Effective precautions (such as using explosion-proof electrical equipments. No static electricity accumulation or metal collision etc) also should be done so as to avoid producting sparks .Flash point of paint , mentioned above on product Data sheet, is the lowest temperature at which mixture of the volatile materails of paint can ignite or explode with air. Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general, Therefore, 200m3of ventilation quantuty per 1Kg solvent (according to the solvent ) is necessary.安全措施Product skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves,eye protection, face masks barrier cream and so on ). Kif paint gets in touch with skin , wass fully with large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.Handle empty containers with care and do not bring about environmental contamination.NOTICE: If consumers have not taken effective safety precautions(Refer to the specfications), our company will NOTbe responsible for any accident.本产品由专业人缘在工业场所使用，使用时请参照本说明书及健康安全手册，如客户在使用本 产品前，未能仔细了解有关产品的健康安全知识，请与本公司联系.该涂料为溶剂型涂料，为避免事故或危险发生,应采取最低限度的安全措施如下： 此涂料为易燃物，并含有挥发性易燃溶剂,，故必须远离火星和明火,严禁在作业场所吸烟，并采取有 效措施，防止火星产生(如采用防爆电器设备,杜绝静电积累，避免金属撞击等)本产品说明书中所 列涂料及溶剂的闪点是引起燃烧的最低温度施工场所应尽量进行通风良好，为消除使用过程中 的爆炸隐患，应保证足够的通风量以维持气体/空气比例不超过最低爆炸极限的10%,通常每千克 溶剂需要200立方米通风量,(与溶剂种类相关)就能维持最低爆炸极限10%的工作环境.采取有效措施以防止皮肤和眼睛与涂料接触(如使用工作服，手套，护目镜,面罩及涂防护油等)如 产品不慎接触到皮肤，应用温水及肥皂或适当的工业清洁剂彻底清洗，如眼睛受到污染，用清水冲 洗至少10分钟,并立即就医.建议佩戴通风面罩以避免吸入漆雾和有害溶剂气体，尤其在通风不良环境下施工时，细心处理旧 漆桶以免污染环境.责任声明：对于未按本公司要求采取有效安全措施儿引起的安全事故，本公司不负任何责任. 来源 江苏纽克莱涂料有限公司 http:/www.nsk-