sony 专业录象机故障代码解决问题

sony 专业录象机故障代码解决问题sony 专业录象机 DSR-1800P 故障代码02-058 Detected an abnormal current in the S reel motor.02-068 Detected an abnormality of reel brake plunger solenoid.02-078 Detected an abnormal current in the T reel motor.02-0B8 Detected an abnormality of pinch plunger solenoid.02-154 Failed to detect the S reel FG by the FG check duringcassette tape insertion.02-174 Failed to detect the T reel FG by the FG check duringcassette tape insertion.02-194 Failed to detect both S and T reel FGs by the FG checkduring cassette tape insertion.02-254 Failed to detect the S reel FG during threading.02-255 Detected the S reel FG during threading.02-274 Failed to detect the T reel FG during threading.02-275 Detected the T reel FG during threading.02-291 Failed to complete winding a tape.02-355 Detected the S reel FG during STOP and STILL.02-375 Detected the T reel FG during STOP and STILL02-395 Detected both S and T reel FGs during STOP and STILL.02-402 Detected an abnormal tape speed during F. FWD and REW.02-403 Detected slack tape during F. FWD and REW.02-454 Failed to detect the S reel FG during F. FWD and REW.02-474 Failed to detect the T reel FG during F. FWD and REW.02-494 Failed to detect both S and T reel FGs during F. FWD and REW.02-496 Detected the abnormal direction of S and T reel rotationduring F. FWD and REW.02-503 Detected slack tape during search.02-554 Failed to detect the S reel FG during search.02-574 Failed to detect the T reel FG during search.02-594 Failed to detect the S and T reel FGs during search.02-596 Detected the abnormal direction of S and T reel rotationduring search.02-603 Detected slack tape during PLAY and REC.02-654 Failed to detect the S reel FG during PLAY and REC.02-674 Failed to detect the T reel FG during PLAY and REC.02-694 Failed to detect both S and T reel FGs during PLAY and REC02-696 Detected the abnormal direction of S and T reel rotationduring PLAY and REC.02-803 Detected slack tape during unthreading.02-854 Failed to detect the S reel FG during unthreading.02-855 Detected the S reel FG during unthreading.02-874 Failed to detect the T reel FG during unthreading.02-875 Detected the T reel FG during unthreading.02-A55 Detected the S reel FG during cassette eject.02-A75 Detected the T reel FG during cassette eject.02-A95 Detected both S and T reel FGs during cassette eject.09-010 Detected abnomal position of cassette compartment.09-020 Detected an abnormality of threading position sensor.09-028 Detected an abnormal current of threading motor.09-224 Failed to detect the threading FG during threading.09-821 Failed to complete unthreading within the specified time09-824 Failed to detect the threading FG during unthreading.DSR-1800P 有时不穿带故障的解决顾客送修一台DSR-1800P机器，自述故障为“有时不穿带”。经试机检查未见不穿带故障。 查看“ ERROR LOG”，发现故障信息有“ E-09-020、09-028、09-824 ”等。检查“M ODE齿轮” 及“FG齿轮”未件有异物；清洁SE-521板；组装机器后试机正常。多次穿退带试机，出现 了 “09-824”故障。更换SE-521板后试机，故障现象依旧（时好时坏）。怀疑）R-428板及 SSP-24 板，更换后无效。更换机芯后故障消失。证明故障仍出在机芯上。再次检查机芯， 更换了所有连接线后仍未解决问题。将示波器连接到DR-428板302-42，观察到当报警时示 波器显示有杂波出现。重新仔细检查机芯，发现“FG齿轮”上有一道轻微划伤，更换新齿 轮后故障消失。由此可分析出：“FG齿轮”上的划伤会导致SE-521板输出FG信号异常， 但此信号处于使机器报警的临界值，导致机器有时能正常工作有时又会报警。MSW-2000P错误信息列表：错误信息列表：NO COMMUNICATION无通信 检测到下部控制面板侧，下部控制面板（KY-464/465电路板）与系统 CPU（SS-89 电路板）间产生异常ERROR-01 磁带故障在穿带或脱带操作中，检测到录像带松弛。ERROR-02 磁带故障在搜索、快进或倒带过程中，检测到录像带松弛和断裂。ERROR-03 磁带故障在录制或播放模式下，检测到录像带松弛和断裂、或供带盘或收带盘 卡住。ERROR-04 磁带故障在快进或倒带过程中，检测到走带速度故障。ERROR-05 磁带故障在插入录像带过程中，检测到供带盘或收带盘运行故障。ERROR-06 磁带张力在录制或播放模式下，检测到磁带张力过大。ERROR-07 主导轴故障检测到主导轴电机故障。ERROR-08 磁鼓故障检测到磁鼓电机故障。ERROR-09 穿带/ 退带电机检测到穿带/ 退带操作故障。ERROR-0A 穿带在穿带模式下，磁带上部操作未完成。ERROR-10 湿气检测到湿气凝结。ERROR-11 磁带头/ 尾传感器同时探测到磁带的头与尾。ERROR-12 带头传感器检测到带头传感器故障。ERROR-13 带尾传感器检测到带尾传感器故障。ERROR-14 风扇电机检测到冷却风扇电机故障。ERROR-20 磁带仓电机检测到磁带仓上下操作故障。ERROR-21 磁带 SFT 电机检测到适合磁带大小的磁带盘运转故障。ERROR-22 磁带位置传感器同时检测到磁带盘的大型磁带与小型磁带的位置。ERROR-23 穿带环传感器同时检测到穿带环的穿带端部与退带端部状态。ERROR-92内部接口 1检测到，系统CPU （在SS-89电路板上）与其他CPU/MPU间的接 口异常。ERROR-93 CPU初始化错误检测到，系统CPU（在SS-89电路板上）与磁鼓CPU（在DR-414 电路板上）间的接口异常。ERROR-95 其他 NV-RAM 错误检测到 FP-119 电路板上的 NV-RAM 运行异常。ERROR-96系统控制NV-RAM错误检测到系统控制系统的NV-RAM（在SS-89电路板上） 运行异常。ERROR-97伺服系统NV-RAM检测到伺服系统的NV-RAM （在DR-414电路板上）运行 异常。ERROR-98 RF NV-RAM 错误检测到RF系统的NV-RAM （在EQ-84电路板上）运行异常。ERROR-99内部接口 2检测到系统CPU （在SS-89电路板上）与伺服CPU （在SS-89电 路板上，或在 EQ-84、DM-123、HIF-1、VPR-64、APR-52、DPR-195 与 DPR-155 电路板 上）间的接口异常。