DMX512控制器说明及介绍

产品概述：products description AT3010D控制器是一款带LCD显示，无线遥控，音频输入，地址编辑 的DMX控制器。 AT3010D controller is a DMX controller with LCD display,wireless control,audio input,IP edition.主要特点 main features 输入电压：AC110V 或 AC220V。input voltage:AC110V or AC220v 输出 DMX 信号符合 DMX512/1990 标准。Input DMX signal by DMX DMX512/1990 standard 具有一个标准的DMX512输出通道，可以实现最多170个全彩点的控制。 With a standard DMX512 output channel,it can realize 170 full color dot control at most内部具有常亮七彩，一致跳变，一致渐变，流水，追逐，中分，堆积等 灯光模式。 Internal has normally on seven color,consistency flash,consistency strobe,smooth,pursuit,halve,accumulate and other lighting mode各种变化效果可分别设定16种不同的变化速度和颜色选择设定。 Each change effects can set 16 different change speed and color selection具有简易的编程功能，可以方便的定义输出灯光效果。 Simple program function,can easliy define input lighting effects编程可自由定义内部的各种变化模式为一个步骤。 Program can easily define all change mode inside to a step.最多可定义8个独立的循环的步骤。 define8 separate independent loop steps具有四个操作按键，可以方便进行功能操作。 With four operation keys,can easily operate具有LCD输出指示，所有功能在LCD上均有操作提示。 With LCD output indication,all function is showed in the LCD.有无线遥控器可以远距离调试和更改操作。 Wireless controller can be used in operation of remote debug and change有音频输入接口，内置有两种音频模式。 With audio input connector,two inside audio mode 具有DMX地址编辑功能，方便地址的修改。 With DMX IP edition function,convienent to modify the ID应用范围：application 小型变化效果的灯光系统的DMX接口输出控制。 DMX connector output control of small change effects产品标准规格表 specification standard diagram产品编号item交流电压输入驱动能力drive控制类型接线方式noDC voltage inputpowercontrol wayconnecting wayAT3010D100V-240V标准模组(standard module)32PCSDMXRJ11典型性能参数 typifcal feature parameters性能项目feature project测试条件test condition最小值min典型值 typical最大值max输出全彩节点 output full color node一个RGB组为一节 点 a RGB group is a node1/170输出DMX通道数Output DMX channel QTY1输出DXM驱动能 力Output DMX drive power标准DMX模组standard DMX module1/32驱动距离drive instance无 中继器 no repeater0/300m最大无损范围 max no-damage range参数项目parameter project代表符号 represent sign最小值min最大值max备注remark输入电压(交流)Input voltage(DC)Vin_AC0AC260V工作温度范围 working temperatureTwork-20C60 C实物照片：real object photo机械尺寸：machine size项目 project规格说明 specification最小值min典型值 typical最大值max长度length160mm宽度width包括天线 include antenna135mm厚度thickness32mm驱动输出接口 RJ11: drive output connector端子 termin al线颜色 line color功能 function备注remark1NC2NC3DMX-4DMX+5GND6SOUT地址编辑时有用到ID is available wheneditting操作说明:operation instructionWELCOME USEAT TECHNOLOGYSTATIC RED 1R1G0G0STATIC YELLOW1R1G1B0STATIC GEEEM ElROG1BOSTATIC CYAN llR0G1B1这是开机画面，开机后显示，约两秒后自动进入到程序模式。 按FUNTION键可以在下面的主功能间切换。Turn on picture,it is showed after turning on.Enter program mode automatically two seconds later.Press FUNTION to switch in the following main function常亮七色模式：normally on seven color mode红色黄色绿色青色蓝色紫色白色STATIC BLUE 1R0G0B1STATIC PURPLE1R1G0B1STATIC WHITE llR1G1B1CHANGE FLASH E2C:00S:31,2,3,4,5,6,7,B,red yellow green cyan blue purple white在常亮模式下，可以通过UP, DOWN按键上来选取这七 种颜色之一。 Under this mode,select one of seven color by pressing UP,DOWN key.C, 可以通过FUNTION按键选取进入下一模式。Enter next mode through FUNTIOND, 在常亮模式下，长按CONFIRM键进入保存参数页面，确认, 下次上电进入当前状态.Under this mode,press CONFIRM for a long time to enter save parameter page,confirm,enter current situation next timeE, 功能代号1。Fucction code1A. 整体跳变功能日输出的颜色可以通过C:后面的参数修改. 默认为 00,即七彩跳变。Whole flash function,output color can be modified by parameter after C:default 00,seven color flashB. 短按CONFIRM键可以在颜色和时间上选择要修改项.C为 颜色,S为显示时间,为当前被选取项.Press CONFIRM for a short time can modify color and time,C is color,S is time, is the current selected optionC. 在时间参数被选取时，跳变的时间可以由UP, DOWN键加 或减。when time parameter selected,Add or minus the flash time by UP,DOWN D.D. 跳变时间共有16级，其中速度1速度最快。Flash time has 16 grades,1is the fastestE. 颜色参数用16进制表示,bit0:红色,bit1:黄,bit2:绿,bit3:青,bit4: 蓝,bit5:紫,bit6:白,bit7:黑.如果该位为1,相应位的颜色被选取，为 0,则该色不输出.如果为00,则默认七彩跳变.Color parameter adopts 16 system,bit0red,bit1yellow,bit2green,bit3 ,bit4 blue,bit5 purple,bit6 white,bit7 black. if it is 1,the corresponding color is selected.if it is 0,it doesnt output the color.if it is 00,default 7 color flash.?；在颜色参数被选取时，按UP或DOWN可以加减该参数.When color parameter selected,press UP or DOWN to add or reduce this parameter.G,可以通过FUNTION按键选取进入下一模式。Enter next mode through FUNTION key.H，在此模式下，长按CONFIRM键进入保存参数页面，确认, 下次上电进入当前状态.In this mode,press CONFIRM to enter save parameter page,confirm,enter current situation next time.I， 功能代号2。Function code 2A. 整体渐变功能，输出的所有灯光按七色顺序渐变，颜色不可 更改。Whole flash function,all output lighting flash according to seven color rank.color is unchangeable.CHANGE FADE1 3C:00S:lB. 短按 CONFIRM 无意义.press CONFIRM for a short time has no meaning.C. 渐变的时间可以由UP, DOWN键选取。Select UP/down to control flash time.D. 渐变时间共有16级，其中速度1速度最快。Flash time has 16 grades,in which 1 is the fastestE. 可以通过FUNTION按键选取进入下一模式。Enter next mode through FUNTIONF. 在此模式下，长按CONFIRM键进入保存参数页面，确信, 下次上电进入当前状态.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current page next timeG. 功能代号3。Function code 3A. 整体渐明渐暗功能出输出的颜色可以通过C:后面的参数修 改.默认为 00,即七彩色。Whole brightness function,modify output color through parameter after C:B. 短按CONFIRM键可以在颜色和时间上选择要修改项.C为 颜色,S为显示时间,为当前被选取项.Press CONFIRM for a short time to select the color and time to be modified.C is color,S is time, is current selected optionCHANGE FADE2 4C:00S:lC. 在时间参数被选取时，跳变的时间可以由UP, DOWN键加或 减。When time parameter selected,control flash time through UP,DOWND. 跳变时间共有16级，其中速度1速度最快。STROBEhas 16 grades,in which 1 is the fastestE,颜色参数用16进制表示,bit0:红色,bit1:黄,bit2:绿,bit3:青,bit4: 蓝,bit5:紫,bit6:白,bit7:黑.如果该位为1,相应位的颜色被选取，为 0,则该色不输出.如果为00,则默认七彩色.Colorparameteradopts16system,bit0red,bit1yellow,bit2 green,bit3 cyan bit4blue,bit5 purple,bit6 white,bit7 black.if it is 1,the correspond color is selected. if it is 0,it doesnt output the color.if it is 00,default 7 color flash.?；在颜色参数被选取时，按UP或DOWN可以加减该参数.When color parameter selected,press UP/DOWN to add or reduce this parameterG，可以通过FUNTION按键选取进入下一模式。Enter next mode through FUNTIONH，在此模式下，长按CONFIRM键进入保存参数页面，确认, 下次上电进入当前状态.In this mode,press CONFIRM to enter save parameter page,confirm,enter current situation next timeI，功能代号4。Function code4A. 七彩追逐功能，输出的灯为七彩交替追逐变化，颜色不可更 改。Seven color pursuit,output light is seven color pursuit by turns,color is not changeable.CHANGE NOVE 5C:00S:lB. 短按CONFIRM 无意义.Press CONFIRM for a short time has no meaning.C. 渐变的时间可以由UP, DOWN键选取。Select flash time through UP,DOWND. 渐变时间共有16级，其中速度1速度最快。Flash time has 16 grades,in which 1 is the fastestE. 可以通过FUNTION按键选取进入下一模式。Enter next mode through FUNTIONI, F,在此模式下，长按CONFIRM键进入保存参数页面，确 信，下次上电进入当前状态.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current page next timeG，功能代号5。Function code5A. 从小地址到大地址流水模式，输出的颜色可以通过C:后面的 参数修改.默认为00,即七彩色。Smooth mode:from small ID to big ID,modify output color through parameter after C:B. 短按CONFIRM键可以在颜色和时间上选择要修改项.C为 颜色,S为显示时间,为当前被选取项.Press CONFIRM for a short time can modify color and time,C is color,S is time, is the current selected optionCHANGE FL伽-6C:00S:3C. 在时间参数被选取时，跳变的时间可以由UP，DOWN键加或 减。When time parameter selected,control strobe timethrough UP,DOWN.D. 跳变时间共有16级，其中速度1速度最快。strobe time has 16 grades,in which 1 is the fastestE, 颜色参数用16进制表示,bit0:红色,bit1:黄,bit2:绿,bit3:青,bit4: 蓝,bit5:紫,bit6:白,bit7:黑.如果该位为1,相应位的颜色被选取，为 0,则该色不输出.如果为00,则默认七彩色.Color parameter adopts 16 system,bit0red,bit1yellow,bit2 green,bit3 cyan bit4blue,bit5 purple,bit6 white,bit7 black .if it is 1,the correspond color is selected.if it is 0,it doesnt output the color.if it is 00,default 7 color?；在颜色参数被选取时，按UP或DOWN可以加减该参数.When color parameter selected,add or reduce this parameter through UP,DOWNG，可以通过FUNTION按键选取进入下一模式。Enter next mode through FUNTIONH，在此模式下，长按CONFIRM键进入保存参数页面，确认, 下次上电进入当前状态.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current page next timeI，功能代号6。Function code6A. 从大地址到小地址流水模式，输出的颜色可以通过C:后面的 参数修改.默认为00,即七彩色。CHANGE FLOW8|C:00S:lPress CONFIRM for a short time has no meaningC. 渐变的时间可以由UP, DOWN键选取。Control flash time through UP,DOWND. 渐变时间共有16级，其中速度1速度最快。flash time has 16 grades,in which 1 is the fastestE，可以通过FUNTION按键选取进入下一模式。Enter next mode through FUNTIONF，在此模式下，长按CONFIRM键进入保存参数页面，确信, 下次上电进入当前状态.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current page next timeG，功能代号8。Function code8A. 渐变从大地址向水地址方向流水模式，颜色不可更改。- Flash from big ID to small ID smooth mode,color is not changeableCHANGE WAVE Specification is only applied to reference of seection and applic