工程英语单词.doc

A- 组件 D-零件 U-标准件 M-原材料 T-工装Rivet 铆钉 bolt 螺栓 HI-LOCK 高锁Tool 工装 clamp 夹具 cleco clamp 鸭嘴夹Chore 掾 CCW 逆时针 CW 顺时针Trim，strencit 挫修 protrude 突出 fay 结合面Tolerance 公差 tangent 切线的 common to 配合Reconvene 提交 enamel 涂油漆 pilot hole 导孔Auxiliary beam，AUX beam 辅梁 clop 销子Drill start 钻点 scrap 作废 drill plate 钻模Nominal 理论值 actually 实际值 radius 圆角Drill bit 钻头 chuck，reamer 铰刀 set 锪窝头Bulkhead=BHD 框 plug guage 塞尺 hinge 铰链Decimal 小数点 十进制 bushings 轴 wrench 扳手Scale 标尺 screw 螺丝钉 torque 扭力楔形垫圈：washer tapered 支架组件：bracket assy 楔形垫片：filler tapered laminated shim 叠形垫片加强件：stiffener 槽形件：channel 腹板：web 电气垫片：shim-elect 电气装置：elec-provisions 电气支架：elec bracket 铆钉：rivet 高锁螺栓：hi-lock锁紧套：collar 护孔环：grommet 黏结剂：adhesive 托盘螺母：nut-plate 盘形件：pan 密封胶：sealant 角材：angle 板形件：pan 梁：beam剪切板：splice plate 支架：bracket , gse support 法兰盘：flange assy支撑角片： support clip 垫片：filler 接地桩：ground stud 接地块：block轴肩螺栓：bolt-shoulder 垫圈：washer 支撑接头组件：ftg.assy-support 枢轴连杆组件：link assy-pivot 保险连杆组件：link assy-fuse 剪切销：shear pin保险销：fuse pin 接地桩：electrical ground stud 接头：fitting closeout 圆弧垫片：radius filler 防火角材：firewall angle 密封支撑：seal support ring底漆：primer 槽型支撑件： support channel 铰链街头组件：hinge fitting assy 保险角材：fallsafe angle 垫片：spacer 螺栓：bolt 铰链梁组件：hinge beam assy梁隔框：beam blkhd 长珩：stringer 支座：support bracket 角片：clip Z形件：ZEE 加强肋：intercostal 支撑夹：support clip 框加强件：frame doubler加强板：doubler 长珩搭接板：strap stringer 耐磨板：grounding block 剪切带：shear tie 角形夹：angle clip 止动锁：latch stop 护板：shield 条带：strip 滑轨组件：track assy 涡流发生器：vortex generator 导板：guide 标牌：marker 侧支撑：side brace 叠层垫片：shim-laminated 衬垫：spacer 滑轮支架：pulley bracket 衬套：bushing 防护件：guard 摩擦板：rub strip 拉板：brace 双面胶：film adhesive 蒙皮：skin 蒙皮壁板：skin panel 加强板：plate-reinforce 框缘：frame chord splice 门组件：access door assy 电闸：switch 断环：break ring 搭接片：jumper assy 间距：gap 边距：edge margin LBL= left body line WL= water line RBL= right body lineTaper filler 楔形垫片 mechanic 机械工人基准：reference 卡板：clamping plate 变形：deformation 擦伤：scratching 公差：tolerance 误差：error 损坏：damage 精加工： 进给量：半精加工：semi finishing machining 车削：turning 车槽：grooving 车螺纹：thread turning 粗加工：rough machining 粗切：rough cut 导轨：guide way 倒角：chamfer 机械加工： machining 加工余量：machining allowance去毛刺：deburring 磨削：grinding 镗削：boring 切削：cutting 铣削：milling 主轴：spindle 钻削：drilling 绞刀：reamer 卷边：crimping 扩口：expansion喷丸成形：peen forming 参数：parameter 几何：geometric 杠杆夹具：lever clamp 弹簧：spring 滚齿：hobbing 环钩：clasp 铰链：hinge 起子：driver 半径规：radius gauge 锉刀：file 千分尺：micrometer gauge 卡尺：callipers 内径千分尺：inside micrometer 锥形：taper 十字起子：cross driver 折痕：crease 喷膜：spray借孔：pull down the edge 化铣台：chem-mill 振动：vibriation 胶带：adhesive 氧化：oxidation 折痕：crease 擦伤：gouges 、工具印：tool marks 划伤：scratches 裂纹：cracks包铝：aluminum clad 珩磨：hone NS=no shear 不抗剪FS=fastener missing 支撑物：brace 扳手：spanner实心铆钉：solid rivet 连接件：spliceMFC：制造商 hole finder 引孔器FWD SLIDING SEAL AFT SLIDING SEAL WINSLOWDrill gaide 带前导的钻头 drill set 顶铁 bucking bar