杂交水稻籽粒分选清选机械装备设计【优秀课程毕业设计含20张CAD图纸带开题报告】-jxsj72
杂交水稻籽粒分选清选机械装备设计
摘 要:杂交水稻工程化制种改变了以前杂交水稻母本于父本间行种植的方式，采用母本与父本混合种植的方式，这就造成了收获后的种子既有母本又有父本；通过实验研究分析可得，母本籽粒的长度约6mm左右，而父本籽粒大约11-12mm，根据两种籽粒的长度的特性的不同，拟设计以窝眼滚轮筒为主要工作部件的清洗机来清选出所需要的母本籽粒。本设计根据当前社会发展需要，自行设计了窝眼滚轮筒，介绍了窝眼滚轮筒国内外研究情况和研究意义。本窝眼滚轮筒重点对分选筒内籽的运动动力学分析，得出了影响籽粒分选的主要因素窝眼分选筒的直径、角速度及斜置倾角，设计计算了各主要部件所需参数并进行了校核，完成了装备图及各主要零件的图纸设计，进行了自我总结。
关键词: 分选；窝眼筒；动力学分析；推料螺旋
Design Of Grain Scalping Machine
Abstract: Hybrid Rice Seed Production of Hybrid Rice changed the previous inter-row cultivation of the female parent in the way male, female and male parent by way of mixed cultivation, which resulted in the seeds after harvest have both male female parent;analysis can be obtained through experiment, the grain length of about 6mm female parent, while the male seed of about 11-12mm, according to the characteristics of the two grains of different length, to be designed to nest eye roller tube as the main working parts of the washing machine?required to settle the election of the female parent grain.The design based on the current social development, to design a roller tube eye socket, eye socket roller tube introduced the situation and significance of domestic and international research.?The roller tube nest eyes focus on the movement of seed tube sorting dynamic analysis of grains obtained the main factor separating the eye socket diameter tube sorting, angular and oblique angle, design and calculation of the major components required?parameters were checked, completed the plans and major parts and equipment design drawings, were self-summary.
Keywords: Separation, Indent cylinder, Dynamic analysis；Pusher spiral
目 录
摘要……………………………………………………………………………………1
关键词…………………………………………………………………………………1
1 前言…………………………………………………………………………………2
2 系统总体方案的确定………………………………………………………………3
2.1 基本结构……………………………………………………………………3
2.2 工作原理……………………………………………………………………3
2.3 系统总体方案设计…………………………………………………………4
3 传动方案的设计……………………………………………………………………4
3.1 电动机的选择………………………………………………………………4
4 传动设计……………………………………………………………………………5
4.1 皮带轮的设计计算…………………………………………………………5
4.2 滚筒链传动设计计算………………………………………………………6
4.3 搅龙链传动设计和计算……………………………………………………8
5 主要部件的设计计算及校核………………………………………………………9
5.1 窝眼型孔……………………………………………………………………9
5.2 分选滚筒……………………………………………………………………9
5.3 滚筒结构设计……………………………………………………………10
5.4 螺旋搅龙…………………………………………………………………11
5.5 螺旋供料器的转速………………………………………………………12
5.6 机架………………………………………………………………………12
6 种子籽粒动力学分析……………………………………………………………12
6.1 长粒种子轴向动力学分析………………………………………………12
6.2 长粒种子轴向动力学分析………………………………………………13
7 传动装置的运动和动力参数……………………………………………………16
7.1各轴转速……………………………………………………………………16
7.2各轴的功率…………………………………………………………………16
7.3各轴转矩……………………………………………………………………16
8 轴的设计校核……………………………………………………………………16
8.1 轴1的设计校核……………………………………………………………16
8.2 轴2的设计校核……………………………………………………………17
8.3重要轴的强度校核…………………………………………………………17
8.4轴承的计算…………………………………………………………………19
8.5轴承载荷校核………………………………………………………………19
9 结论………………………………………………………………………………19
参考文献 ……………………………………………………………………………21
致谢 …………………………………………………………………………………23
【详情如下】【需要咨询购买全套设计请加QQ1459919609】
半圆加强板.dwg
图纸合计20张.dwg
垫片.dwg
套筒.dwg
小支架.dwg
承种槽.dwg
推料螺旋.dwg
搅龙固定架.dwg
搅龙固定盘.dwg
支承轴.dwg
支承轴2.dwg
支承轴部件.dwg
支架1.dwg
文件清单.txt
杂交水稻籽粒分选清选机械装备设计.doc
杂交水稻籽粒分选清选机械装备设计开题论证审批表.doc
滚筒.dwg
环形防漏槽.dwg
目录.doc
窝眼滚筒装配图.dwg
端面挡圈.dwg
箱盖.dwg
网架.dwg
进料斗.dwg
防堵拔齿.dwg
