中文版东芝压铸机油圧回路说明.ppt

1,350油圧回路,东芝机械股份有限公司压铸技术中心,液压泵油圧回路合模油圧回路射出油圧回路,鋳造,2,350阀配置图,3,350阀配置图,4,350阀配置图,5,5,25,1,1,2,4.5,3,241,1,联泵液压回路阀,6,5,1,2,4.5,3,241,1,5,压力油量调整阀（阀）,比例电磁式流量调整阀减压控制阀比例电磁式压力控制阀主溢流阀（压力辅正阀）控制阀安全阀,圧力控制阀压力油量调整阀（阀）,联泵液压回路阀,压力油量调整阀（阀）,射出回路,7,1,2,22,1,4,5,25,24,3,1,24,2,1,1,5,4.5,350合模頂出中子動作,压力油量调整阀（阀）,8,3,22,2,1,24,1,4.5,5,1,350合模动作图,Run-Around回路合模油缸的把回来的油进入了给方面归还的回路速度大的特征,压力油量调整阀（阀）,9,3,22,2,1,24,1,5,4.5,1,压力油量调整阀（阀）,10,3,22,2,1,24,1,5,4.5,1,压力油量调整阀（阀）,11,3,22,2,1,24,1,5,4.5,1,压力油量调整阀（阀）,12,3,22,2,1,24,1,5,4.5,1,压力油量调整阀（阀）,13,3,22,2,1,24,1,5,4.5,1,压力油量调整阀（阀）,14,3,22,2,1,24,1,5,4.5,1,压力油量调整阀（阀）,15,Injectionsensor,12,11,350射出油圧回路,3,16,C2G16,1,215,12,11,Injectionsensor,3,17,C2G16,215,1,12,11,Injectionsensor,3,18,C2G16,1,215,12,11,Injectionsensor,3,19,C2G16,1,215,12,11,Injectionsensor,3,背压消除油缸,20,C2G16,1,215,12,11,Injectionsensor,3,21,C2G16,1,215,12,11,Injectionsensor,3,22,C2G16,1,215,12,11,Injectionsensor,3,23,C2G16,1,215,12,11,Injectionsensor,3,24,C2G16,1,215,Injectionsensor,12,11,3,25,C2G16,1,215,12,11,Injectionsensor,3,26,C2G16,1,215,Injectionsensor,12,11,3,27,C2G16,1,215,G,G2,G,G4,2,G1,11,15,C2G20,SV1,28,1,2,C2G19,C2G21,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,350射出油圧回路,自动ON,G,G2,G,G4,2,G1,11,C2G20,SV1,29,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,合模,G,G2,G,G4,2,G1,11,C2G20,SV1,30,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,低速射出多段,G,G2,G,G4,2,G1,11,C2G20,SV1,31,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,低速射出,G,G2,G,G4,2,G1,11,C2G20,SV1,32,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,高速射出,G,G2,G,G4,2,G1,11,C2G20,SV1,33,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,减速射出,G,G2,G,G4,2,G1,11,C2G20,SV1,34,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G15,C2G21,G15,15,增压射出,G,G2,G,G4,2,G1,11,C2G20,SV1,35,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,增压关,G,G2,G,G4,2,G1,11,C2G20,SV1,36,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,开模射出前進,G,G2,G,G4,2,G1,11,C2G20,SV1,37,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,射出前進限,G,G2,G,G4,2,G1,11,C2G20,SV1,38,1,2,C2G19,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,C2G21,15,射出返回,G,G2,G,G4,2,G1,11,C2G20,SV1,39,1,2,C2G19,C2G21,G37,C2G37,G13,G33,G17,Injectionsensor,C2G16,15,1循环鑄造完毕,40,1,1,1,241,1,2,1,1,2,13.5,11,充填,储气罐液压回路350,压力油量调整阀（阀）,射出油缸,41,1,1,1,241,1,2,充填,1,1,2,8.5,11,储气罐液压回路350,充填,压力油量调整阀（阀）,射出油缸,42,