EN60598-1第四章节导读

Energy-related Product,Click to edit Master text styles,Second level,Third level,Fourth level,*,Safety testing,*,*,confidential,Energy-related Product,Click to edit Master text styles,Second level,Third level,Fourth level,*,Cl.4 of EN 60598-1,general constructional requirements for luminaires(Introduction),Eurofins Shanghai,1,General construction,4.2 Replaceable component,Key words:sufficient space,no difficulty,no impairing safety,Examples not fit the requirements:,The luminary should be all detached if the lamp need to be replaced.,The protective device should be removed when the starter need to be replaced.,No marking or instructions in the manual showing how to replace the batteries.,General construction,4.3 Wireways,Key words:No sharp edges,burrs,flashes.No abrasion,Example:EN 60598-2-5,General construction,4.4 Lampholder,4.4.1,Key words:Safety not impaired during insertion of the lamp,4.4.2,Key words:Reliable electrical contact,4.4.3,Key words:Independence,4.4.4,Key words:Mechanical strength,General construction,General construction,General construction,General construction,4.4.7,For insulation material for luminaries other than the ordinary,tracking test is needed,4.4.8,Means for retaining the lamp shall be provided by other parts of the luminaire.,4.4.9,NOTE Examples of such ELV fits are:G4,GU4,GY4,GX5.3,GU5.3,G6.35,GY6.35,GU7 and G53.,General construction,4.6 Terminal block,General construction,General construction,4.7 Terminals and supply connections,4.7.1,General construction,General construction,Figure 19,General construction,4.7.2,Test:,Test:,General construction,4.7.3,NOTE 3,General construction,4.7.3.1,General construction,4.7.4,4.7.5,Key words:Heat-resistance of the wire,General construction,4.7.6,General construction,4.8 Switches,OSM decision,General construction,OSM decision,General construction,4.9 Insulating linings and sleeves,4.9.1,4.9.2,General construction,4.10 Double and reinforced insulation,4.10.1,General construction,4.10.2,General construction,4.10.3,General construction,4.11 Electric connection and current-carrying parts,4.11.1,Inconformity,Example:,General construction,4.11.2,自攻螺钉、自切螺钉和变形成纹螺钉,General construction,4.11.3,4.11.4,Key words:at least 50%copper,corrosion,4.11.5,General construction,4.11.6,General construction,4.12 Screws and connections(mechanical)and glands,4.12.1,我也没看懂,General construction,4.12.2,4.12.4,General construction,4.12.5,General construction,4.13 Mechanical Strength,4.13.1,General construction,4.13.3,4.13.6,General construction,Figure 25,General construction,4.14 Suspension and means of adjustment,4.14.1,General construction,4.14.2,用导线悬挂的固定式灯具导线的拉力测试？,不懂,General construction,4.14.3,4.14.4,4.14.5,Key words:guide pulleys,no harm to the cord,General construction,4.14.6,General construction,4.15 Flammable material,4.15.1,Figure 4:,General construction,4.15.2,General construction,4.16 Luminaires for mounting on normally flammable surfaces,4.16.1(,需要讨论一下,),General construction,以下这种产品可以被认为是符合4.16.1的要求吗？,驱动按照EN 61347-2-13 做独立式驱动随机测试,产品按照EN 61347-2-2 测试,General construction,4.16.3,4.17 Drain hole,General construction,4.18 Resistance to corrosion,4.18.1,Key words:Ferrous parts,resistance to corrosion,4.18.2,Key words:Contact parts of copper material,resistance to corrosion,4.18.3,Key words:Aluminium parts,resistance to corrosion,注意：铜和铝不能直接接触,具体可参考,60950-1,：,Clause 2.6.5.6,及,Annex J,General construction,Annex J,General construction,4.20 Rough service luminaires Vibration requirements,4.21 Protective shield,4.22 attachments to lamp,注意：LED T8 灯管的认证时,别遗漏了该要求,General construction,4.23 Semi-luminaires,4.24 UV radiation,4.25 Mechanical hazard,4.26 Short-circuit protection,4.27 Terminal blocks with integrated screwless earthing contacts,Annex V,