网架吊装专项施工方案

编号：SJ1F.1703-11 创新中心续建工程（公共服务平台）项目网架结构吊装专项施工方案编 制 人：审 核 人：批 准 人：日期:目录一、编制依据 .1二、工程概况 .2三、施工准备 .3四、网架吊装部署 .3五、网架单元计算 .6六、营业执照及税务登记证.41一、编制依据1.1 工程相关文件创新中心续建工程（公共服务平台）项目网架工程建筑图创新中心续建工程（公共服务平台）项目网架工程结构图网架结构施工方案二、工程概况工程名称创新中心续建工程（公共服务平台）项目质量标准符合现行的质量验收规范，达到合格标准。工程简介本工程为太原不锈钢产业园区创新中心续建工程整个研发中心的裙房部分网架结构，该网架为正放四角锥焊接空心球结构，上弦多点支承，网架短向跨26.0 米，长向跨度35.7 米,厚度 1.5 米。两台吊车同时起吊，因网架面积35.7m*26m 较大，所以要求吊车司机配合度相当高。本工程网架在室外地坪拼装完成，一次性吊到楼内指定位置。吊装公司山西二牛吊装有限公司三、施工准备3.1 组织架构3.2 机具准备机具设备计划机械或设备名称规格型号数量备注汽车吊车260 吨两台吊装网架交流或直流焊机4 台预埋板焊接四、网架吊装部署4.1 整体安装部署网架安装计划先在地面拼装完成除屋面以外，利用汽车吊吊装屋面上与屋面上预埋板焊接施工方案。在距楼7m位置进行拼装完成，然后用260t 的两辆吊车，共同起吊至屋面。现场平面图如下:4.3 网架的提升4.3.1 网架提升的机具选择网架的提升计划采用两台260 吨汽车吊，吊绳尺寸选用22#，吊点为网架下弦部位，出臂顺序为222111，钢丝绳选取6 分，经过计算汽车吊吊装网架为31 吨，单台汽车吊乘以1.2 倍系数负荷为18.6 吨。具体性能表如下：4.3.2 网架提升示意图五、网架单元计算 5.1 网架单元信息（单元号、截面、长度详见网架结构设计图纸）网架单元信息表单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论10 60 x3.5 2.700 621 0.8 0.8 0.01 0.00 108 满足11 60 x3.5 2.750 621 3.9 3.9 0.03 0.00 110 满足12 60 x3.5 2.750 621 1.8 1.8 0.01 0.00 110 满足16 60 x3.5 3.000 621 2.7 2.7 0.02 0.00 120 满足17 60 x3.5 3.000 621 4.4 4.4 0.03 0.00 120 满足18 60 x3.5 2.800 621 0.8 0.8 0.01 0.00 112 满足19 60 x3.5 2.700 621 0.7 0.7 0.00 0.00 108 满足20 60 x3.5 2.750 621 5.3 5.3 0.04 0.00 110 满足26 60 x3.5 3.000 621 5.8 5.8 0.04 0.00 120 满足27 60 x3.5 2.800 621 0.7 0.7 0.00 0.00 112 满足28 60 x3.5 2.700 621 0.6 0.6 0.00 0.00 108 满足29 60 x3.5 2.750 621 6.6 6.6 0.05 0.00 110 满足36 60 x3.5 2.800 621 0.6 0.6 0.00 0.00 112 满足37 60 x3.5 2.700 621 0.7 0.7 0.01 0.00 108 满足45 60 x3.5 2.800 621 0.7 0.7 0.01 0.00 112 满足55 60 x3.5 2.700 621 0.9 0.9 0.01 0.00 108 满足63 60 x3.5 2.800 621 0.9 0.9 0.01 0.00 112 满足64 60 x3.5 2.700 621 0.7 0.7 0.01 0.00 108 满足72 60 x3.5 2.800 621 0.7 0.7 0.01 0.00 112 满足73 60 x3.5 2.700 621 0.7 0.7 0.01 0.00 108 满足81 60 x3.5 2.800 621 0.7 0.7 0.01 0.00 112 满足82 60 x3.5 2.700 621 0.9 0.9 0.01 0.00 108 满足90 60 x3.5 2.800 621 0.9 0.9 0.01 0.00 112 满足100 60 x3.5 2.700 621 0.7 0.7 0.01 0.00 108 满足108 60 x3.5 2.800 621 0.7 0.7 0.01 0.00 112 满足109 60 x3.5 2.700 621 0.6 0.6 0.00 0.00 108 满足110 60 x3.5 2.750 621 6.6 6.6 0.05 0.00 110 满足117 60 x3.5 2.800 621 0.6 0.6 0.00 0.00 112 满足118 60 x3.5 2.700 621 0.7 0.7 0.00 0.00 108 满足119 60 x3.5 2.750 621 5.3 5.3 0.04 0.00 110 满足125 60 x3.5 3.000 621 5.8 5.8 0.04 0.00 120 满足126 60 x3.5 2.800 621 0.7 0.7 0.00 0.00 112 满足127 60 x3.5 2.700 621 0.8 0.8 0.01 0.00 108 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论128 60 x3.5 2.750 621 3.9 3.9 0.03 0.00 110 满足129 60 x3.5 2.750 621 1.8 1.8 0.01 0.00 110 满足133 60 x3.5 3.000 621 2.7 2.7 0.02 0.00 120 满足134 60 x3.5 3.000 621 4.4 4.4 0.03 0.00 120 满足135 60 x3.5 2.800 621 0.8 0.8 0.01 0.00 112 满足148 60 x3.5 2.370 621-3.5-3.5 0.03 0.04 95 满足149 60 x3.5 2.370 621-7.5-7.5 0.06 0.10 95 满足155 60 x3.5 2.370 621-7.5-7.5 0.06 0.10 95 满足156 60 x3.5 2.370 621-3.5-3.5 0.03 0.04 95 满足160 60 x3.5 2.370 621 0.5 0.5 0.00 0.00 95 满足164 60 x3.5 2.370 621-10.3-10.3 0.08 0.13 95 满足165 60 x3.5 2.400 621-18.0-18.0 0.14 0.23 96 满足169 60 x3.5 2.400 621-18.0-18.0 0.14 0.23 96 满足170 60 x3.5 2.370 621-10.3-10.3 0.08 0.13 95 满足174 60 x3.5 2.370 621 0.5 0.5 0.00 0.00 95 满足175 60 x3.5 2.370 621 0.5 0.5 0.00 0.00 95 满足176 60 x3.5 2.370 621 2.8 2.8 0.02 0.00 95 满足188 60 x3.5 2.370 621 2.8 2.8 0.02 0.00 95 满足189 60 x3.5 2.370 621 0.5 0.5 0.00 0.00 95 满足205 60 x3.5 2.370 621 0.4 0.4 0.00 0.00 95 满足219 60 x3.5 2.370 621 0.4 0.4 0.00 0.00 95 满足220 60 x3.5 2.370 621 0.4 0.4 0.00 0.00 95 满足234 60 x3.5 2.370 621 0.4 0.4 0.00 0.00 95 满足250 60 x3.5 2.370 621 0.5 0.5 0.00 0.00 95 满足251 60 x3.5 2.370 621 3.4 3.4 0.03 0.00 95 满足263 60 x3.5 2.370 621 3.4 3.4 0.03 0.00 95 满足264 60 x3.5 2.370 621 0.5 0.5 0.00 0.00 95 满足265 60 x3.5 2.370 621 0.5 0.5 0.00 0.00 95 满足269 60 x3.5 2.370 621-11.1-11.1 0.08 0.14 95 满足270 60 x3.5 2.400 621-18.7-18.7 0.14 0.24 96 满足274 60 x3.5 2.400 621-18.7-18.7 0.14 0.24 96 满足275 60 x3.5 2.370 621-11.1-11.1 0.08 0.14 95 满足279 60 x3.5 2.370 621 0.5 0.5 0.00 0.00 95 满足283 60 x3.5 2.370 621-4.3-4.3 0.03 0.05 95 满足284 60 x3.5 2.370 621-8.7-8.7 0.07 0.11 95 满足290 60 x3.5 2.370 621-8.7-8.7 0.07 0.11 95 满足291 60 x3.5 2.370 621-4.3-4.3 0.03 0.05 95 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论295 60 x3.5 1.975 621-2.0-2.0 0.01 0.02 79 满足296 60 x3.5 2.750 621-2.0-2.0 0.01 0.03 110 满足298 60 x3.5 3.000 621-2.7-2.7 0.02 0.05 120 满足299 60 x3.5 3.000 621-3.1-3.1 0.02 0.05 120 满足301 60 x3.5 3.000 621-3.2-3.2 0.02 0.06 120 满足303 60 x3.5 1.975 621-2.6-2.6 0.02 0.03 79 满足304 60 x3.5 2.750 621-9.1-9.1 0.07 0.16 124 满足305 60 x3.5 2.875 621-1.6-1.6 0.01 0.03 129 满足309 60 x3.5 3.000 621-10.2-10.2 0.08 0.21 135 满足310 60 x3.5 2.200 621-2.5-2.5 0.02 0.03 88 满足311 60 x3.5 1.975 621-1.9-1.9 0.01 0.02 79 满足318 60 x3.5 2.200 621-2.1-2.1 0.02 0.02 88 满足319 60 x3.5 1.975 621-3.2-3.2 0.02 0.03 79 满足326 60 x3.5 2.200 621-3.5-3.5 0.03 0.04 88 满足343 60 x3.5 1.975 621-0.3-0.3 0.00 0.00 79 满足350 60 x3.5 2.200 621 0.3 0.3 0.00 0.00 88 满足351 60 x3.5 1.975 621-0.1-0.1 0.00 0.00 79 满足358 60 x3.5 2.200 621 0.1 0.1 0.00 0.00 88 满足359 60 x3.5 1.975 621-0.3-0.3 0.00 0.00 79 满足366 60 x3.5 2.200 621 0.3 0.3 0.00 0.00 88 满足383 60 x3.5 1.975 621-3.2-3.2 0.02 0.03 79 满足390 60 x3.5 2.200 621-3.5-3.5 0.03 0.04 88 满足391 60 x3.5 1.975 621-1.9-1.9 0.01 0.02 79 满足398 60 x3.5 2.200 621-2.1-2.1 0.02 0.02 88 满足399 60 x3.5 1.975 621-2.6-2.6 0.02 0.03 79 满足400 60 x3.5 2.750 621-9.1-9.1 0.07 0.16 124 满足401 60 x3.5 2.875 621-1.6-1.6 0.01 0.03 129 满足405 60 x3.5 3.000 621-10.2-10.2 0.08 0.21 135 满足406 60 x3.5 2.200 621-2.5-2.5 0.02 0.03 88 满足407 60 x3.5 1.975 621-2.0-2.0 0.01 0.02 79 满足408 60 x3.5 2.750 621-2.0-2.0 0.01 0.03 110 满足410 60 x3.5 3.000 621-2.7-2.7 0.02 0.05 120 满足411 60 x3.5 3.000 621-3.1-3.1 0.02 0.05 120 满足413 60 x3.5 3.000 621-3.2-3.2 0.02 0.06 120 满足418 60 x3.5 2.370 621 3.6 3.6 0.03 0.00 95 满足425 60 x3.5 2.370 621 3.6 3.6 0.03 0.00 95 满足429 60 x3.5 2.250 621-1.9-1.9 0.01 0.02 90 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论432 60 x3.5 2.370 621 2.2 2.2 0.02 0.00 95 满足439 60 x3.5 2.370 621 2.2 2.2 0.02 0.00 95 满足442 60 x3.5 2.250 621-1.9-1.9 0.01 0.02 90 满足443 60 x3.5 2.250 621 4.4 4.4 0.03 0.00 101 满足456 60 x3.5 2.250 621 4.4 4.4 0.03 0.00 101 满足457 60 x3.5 2.250 621-3.7-3.7 0.03 0.04 90 满足470 60 x3.5 2.250 621-3.7-3.7 0.03 0.04 90 满足471 60 x3.5 2.250 621-4.5-4.5 0.03 0.05 90 满足484 60 x3.5 2.250 621-4.5-4.5 0.03 0.05 90 满足485 60 x3.5 2.250 621-4.1-4.1 0.03 0.05 90 满足498 60 x3.5 2.250 621-4.1-4.1 0.03 0.05 90 满足499 60 x3.5 2.250 621 4.2 4.2 0.03 0.00 101 满足512 60 x3.5 2.250 621 4.2 4.2 0.03 0.00 101 满足513 60 x3.5 2.250 621-2.2-2.2 0.02 0.03 90 满足526 60 x3.5 2.250 621-2.2-2.2 0.02 0.03 90 满足530 60 x3.5 2.370 621 5.1 5.1 0.04 0.00 95 满足537 60 x3.5 2.370 621 5.1 5.1 0.04 0.00 95 满足542 60 x3.5 2.077 621-1.3-1.3 0.01 0.01 83 满足544 60 x3.5 1.935 621 3.2 3.2 0.02 0.00 77 满足545 60 x3.5 2.417 621 0.6 0.6 0.00 0.00 97 满足546 60 x3.5 2.417 621-2.1-2.1 0.02 0.03 97 满足547 60 x3.5 2.297 621-0.2-0.2 0.00 0.00 92 满足548 60 x3.5 2.297 621 2.4 2.4 0.02 0.00 92 满足551 60 x3.5 2.297 621-0.5-0.5 0.00 0.01 92 满足552 60 x3.5 2.297 621-3.2-3.2 0.02 0.04 92 满足554 60 x3.5 2.491 621 1.6 1.6 0.01 0.00 100 满足555 60 x3.5 2.374 621 4.6 4.6 0.03 0.00 95 满足557 60 x3.5 2.491 621-2.4-2.4 0.02 0.03 100 满足558 60 x3.5 2.491 621-1.9-1.9 0.01 0.03 100 满足559 60 x3.5 2.374 621 2.4 2.4 0.02 0.00 95 满足560 60 x3.5 2.374 621 2.6 2.6 0.02 0.00 95 满足561 60 x3.5 2.491 621 1.2 1.2 0.01 0.00 100 满足564 60 x3.5 2.374 621 5.3 5.3 0.04 0.00 95 满足567 60 x3.5 2.374 621-3.3-3.3 0.02 0.04 95 满足568 60 x3.5 2.374 621-0.3-0.3 0.00 0.00 95 满足569 60 x3.5 2.491 621-2.1-2.1 0.02 0.03 100 满足570 60 x3.5 2.491 621 0.2 0.2 0.00 0.00 100 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论571 60 x3.5 2.374 621 2.9 2.9 0.02 0.00 95 满足572 60 x3.5 2.374 621-0.3-0.3 0.00 0.00 95 满足573 60 x3.5 2.108 621-1.0-1.0 0.01 0.01 84 满足575 60 x3.5 1.968 621 3.3 3.3 0.03 0.00 79 满足577 60 x3.5 2.840 621-0.2-0.2 0.00 0.00 114 满足578 60 x3.5 2.004 621-0.7-0.7 0.01 0.01 80 满足579 60 x3.5 2.840 621-2.2-2.2 0.02 0.04 114 满足580 60 x3.5 2.004 621 3.2 3.2 0.02 0.00 80 满足581 60 x3.5 2.355 621-3.8-3.8 0.03 0.05 94 满足582 60 x3.5 2.355 621-4.7-4.7 0.04 0.06 94 满足583 60 x3.5 2.355 621-1.3-1.3 0.01 0.02 94 满足584 60 x3.5 2.355 621 10.8 10.8 0.08 0.00 94 满足585 60 x3.5 2.355 621 1.9 1.9 0.01 0.00 106 满足586 60 x3.5 2.355 621 5.0 5.0 0.04 0.00 106 满足587 60 x3.5 2.355 621 13.6 13.6 0.10 0.00 106 满足588 60 x3.5 2.355 621 12.2 12.2 0.09 0.00 106 满足589 60 x3.5 2.430 621-7.7-7.7 0.06 0.10 97 满足590 60 x3.5 2.430 621-1.2-1.2 0.01 0.02 97 满足591 60 x3.5 2.430 621 11.8 11.8 0.09 0.00 97 满足592 60 x3.5 2.430 621-1.8-1.8 0.01 0.02 97 满足593 60 x3.5 2.430 621-2.2-2.2 0.02 0.03 97 满足594 60 x3.5 2.430 621-1.9-1.9 0.01 0.03 97 满足595 60 x3.5 2.430 621 2.4 2.4 0.02 0.00 97 满足596 60 x3.5 2.430 621 2.8 2.8 0.02 0.00 97 满足597 60 x3.5 2.430 621-1.4-1.4 0.01 0.02 97 满足598 60 x3.5 2.430 621-8.3-8.3 0.06 0.11 97 满足599 60 x3.5 2.430 621-2.5-2.5 0.02 0.03 97 满足600 60 x3.5 2.430 621 13.3 13.3 0.10 0.00 97 满足601 60 x3.5 2.430 621 4.8 4.8 0.04 0.00 109 满足602 60 x3.5 2.430 621 1.3 1.3 0.01 0.00 109 满足603 60 x3.5 2.430 621 11.0 11.0 0.08 0.00 109 满足604 60 x3.5 2.430 621 13.6 13.6 0.10 0.00 109 满足605 60 x3.5 2.430 621-4.9-4.9 0.04 0.06 97 满足606 60 x3.5 2.430 621-4.0-4.0 0.03 0.05 97 满足607 60 x3.5 2.430 621 11.6 11.6 0.09 0.00 97 满足608 60 x3.5 2.430 621-1.7-1.7 0.01 0.02 97 满足609 60 x3.5 2.036 621-0.6-0.6 0.00 0.01 81 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论610 60 x3.5 2.840 621 0.2 0.2 0.00 0.00 114 满足611 60 x3.5 2.036 621 3.1 3.1 0.02 0.00 81 满足612 60 x3.5 2.840 621-2.5-2.5 0.02 0.04 114 满足613 60 x3.5 2.840 621 1.3 1.3 0.01 0.00 114 满足614 60 x3.5 2.004 621 0.9 0.9 0.01 0.00 80 满足615 60 x3.5 2.840 621-3.1-3.1 0.02 0.05 114 满足616 60 x3.5 2.004 621 1.3 1.3 0.01 0.00 80 满足617 60 x3.5 2.355 621-4.5-4.5 0.03 0.06 94 满足618 60 x3.5 2.355 621 2.8 2.8 0.02 0.00 94 满足619 60 x3.5 2.355 621-8.0-8.0 0.06 0.10 94 满足620 60 x3.5 2.355 621 10.7 10.7 0.08 0.00 94 满足621 60 x3.5 2.355 621-28.2-28.2 0.21 0.41 106 满足622 60 x3.5 2.355 621-28.9-28.9 0.22 0.42 106 满足623 60 x3.5 2.355 621-45.7-45.7 0.34 0.66 106 满足624 60 x3.5 2.355 621-48.4-48.4 0.36 0.70 106 满足625 60 x3.5 2.430 621 3.9 3.9 0.03 0.00 97 满足626 60 x3.5 2.430 621-3.6-3.6 0.03 0.05 97 满足627 60 x3.5 2.430 621 12.1 12.1 0.09 0.00 97 满足628 60 x3.5 2.430 621-10.9-10.9 0.08 0.14 97 满足629 60 x3.5 2.430 621 1.5 1.5 0.01 0.00 97 满足630 60 x3.5 2.430 621 1.8 1.8 0.01 0.00 97 满足631 60 x3.5 2.430 621-0.7-0.7 0.01 0.01 97 满足632 60 x3.5 2.430 621-1.1-1.1 0.01 0.01 97 满足633 60 x3.5 2.430 621-3.7-3.7 0.03 0.05 97 满足634 60 x3.5 2.430 621 4.2 4.2 0.03 0.00 97 满足635 60 x3.5 2.430 621-11.3-11.3 0.08 0.15 97 满足636 60 x3.5 2.430 621 12.3 12.3 0.09 0.00 97 满足637 60 x3.5 2.430 621-30.3-30.3 0.23 0.46 109 满足638 60 x3.5 2.430 621-30.5-30.5 0.23 0.46 109 满足639 60 x3.5 2.430 621-51.5-51.5 0.39 0.78 109 满足640 60 x3.5 2.430 621-48.1-48.1 0.36 0.72 109 满足641 60 x3.5 2.430 621 4.1 4.1 0.03 0.00 97 满足642 60 x3.5 2.430 621-4.4-4.4 0.03 0.06 97 满足643 60 x3.5 2.430 621 9.9 9.9 0.07 0.00 97 满足644 60 x3.5 2.430 621-8.5-8.5 0.06 0.11 97 满足645 60 x3.5 2.036 621 1.1 1.1 0.01 0.00 81 满足646 60 x3.5 2.840 621 1.6 1.6 0.01 0.00 114 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论647 60 x3.5 2.036 621 1.1 1.1 0.01 0.00 81 满足648 60 x3.5 2.840 621-3.4-3.4 0.03 0.05 114 满足652 60 x3.5 2.004 621-1.1-1.1 0.01 0.01 80 满足653 60 x3.5 2.355 621 0.6 0.6 0.00 0.00 94 满足655 60 x3.5 2.355 621-11.1-11.1 0.08 0.14 94 满足656 60 x3.5 2.355 621-3.6-3.6 0.03 0.05 94 满足657 60 x3.5 2.355 621 18.5 18.5 0.14 0.00 94 满足658 60 x3.5 2.355 621 17.5 17.5 0.13 0.00 94 满足659 60 x3.5 2.355 621-15.9-15.9 0.12 0.20 94 满足660 60 x3.5 2.355 621-18.5-18.5 0.14 0.23 94 满足661 60 x3.5 2.430 621 17.9 17.9 0.13 0.00 97 满足662 60 x3.5 2.430 621 2.1 2.1 0.02 0.00 97 满足663 60 x3.5 2.430 621-3.7-3.7 0.03 0.05 97 满足664 60 x3.5 2.430 621-14.2-14.2 0.11 0.19 97 满足665 60 x3.5 2.430 621 7.3 7.3 0.05 0.00 97 满足666 60 x3.5 2.430 621 7.5 7.5 0.06 0.00 97 满足667 60 x3.5 2.430 621-6.5-6.5 0.05 0.08 97 满足668 60 x3.5 2.430 621-6.1-6.1 0.05 0.08 97 满足669 60 x3.5 2.430 621 2.6 2.6 0.02 0.00 97 满足670 60 x3.5 2.430 621 18.2 18.2 0.14 0.00 97 满足671 60 x3.5 2.430 621-14.9-14.9 0.11 0.19 97 满足672 60 x3.5 2.430 621-3.8-3.8 0.03 0.05 97 满足673 60 x3.5 2.430 621 19.1 19.1 0.14 0.00 97 满足674 60 x3.5 2.430 621 21.1 21.1 0.16 0.00 97 满足675 60 x3.5 2.430 621-20.5-20.5 0.15 0.27 97 满足676 60 x3.5 2.430 621-17.9-17.9 0.13 0.23 97 满足678 60 x3.5 2.430 621 0.9 0.9 0.01 0.00 97 满足679 60 x3.5 2.430 621-3.7-3.7 0.03 0.05 97 满足680 60 x3.5 2.430 621-11.5-11.5 0.09 0.15 97 满足683 60 x3.5 2.036 621-1.0-1.0 0.01 0.01 81 满足688 60 x3.5 2.004 621-2.8-2.8 0.02 0.03 80 满足692 60 x3.5 2.355 621-3.2-3.2 0.02 0.04 94 满足693 60 x3.5 2.355 621 8.5 8.5 0.06 0.00 94 满足694 60 x3.5 2.355 621 10.1 10.1 0.08 0.00 94 满足695 60 x3.5 2.355 621-7.5-7.5 0.06 0.09 94 满足696 60 x3.5 2.355 621-9.2-9.2 0.07 0.12 94 满足697 60 x3.5 2.430 621 10.0 10.0 0.07 0.00 97 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论698 60 x3.5 2.430 621 8.3 8.3 0.06 0.00 97 满足699 60 x3.5 2.430 621-4.6-4.6 0.03 0.06 97 满足700 60 x3.5 2.430 621-11.2-11.2 0.08 0.15 97 满足701 60 x3.5 2.430 621 10.0 10.0 0.08 0.00 97 满足702 60 x3.5 2.430 621 10.1 10.1 0.08 0.00 97 满足703 60 x3.5 2.430 621-9.0-9.0 0.07 0.12 97 满足704 60 x3.5 2.430 621-8.6-8.6 0.06 0.11 97 满足705 60 x3.5 2.430 621 8.3 8.3 0.06 0.00 97 满足706 60 x3.5 2.430 621 10.7 10.7 0.08 0.00 97 满足707 60 x3.5 2.430 621-11.8-11.8 0.09 0.15 97 满足708 60 x3.5 2.430 621-4.6-4.6 0.03 0.06 97 满足709 60 x3.5 2.430 621 11.3 11.3 0.08 0.00 97 满足710 60 x3.5 2.430 621 9.8 9.8 0.07 0.00 97 满足711 60 x3.5 2.430 621-10.3-10.3 0.08 0.13 97 满足712 60 x3.5 2.430 621-8.6-8.6 0.06 0.11 97 满足715 60 x3.5 2.430 621-3.3-3.3 0.03 0.04 97 满足719 60 x3.5 2.036 621-2.4-2.4 0.02 0.03 81 满足725 60 x3.5 2.362 621 1.1 1.1 0.01 0.00 94 满足726 60 x3.5 2.362 621 5.1 5.1 0.04 0.00 94 满足727 60 x3.5 2.362 621-3.5-3.5 0.03 0.04 94 满足729 60 x3.5 2.362 621 2.5 2.5 0.02 0.00 94 满足730 60 x3.5 2.362 621 6.9 6.9 0.05 0.00 94 满足731 60 x3.5 2.362 621-3.7-3.7 0.03 0.05 94 满足732 60 x3.5 2.362 621-2.4-2.4 0.02 0.03 94 满足733 60 x3.5 2.437 621 3.2 3.2 0.02 0.00 97 满足734 60 x3.5 2.437 621 8.0 8.0 0.06 0.00 97 满足735 60 x3.5 2.437 621-1.3-1.3 0.01 0.02 97 满足736 60 x3.5 2.437 621-6.2-6.2 0.05 0.08 97 满足737 60 x3.5 2.437 621 8.4 8.4 0.06 0.00 97 满足738 60 x3.5 2.437 621 8.5 8.5 0.06 0.00 97 满足739 60 x3.5 2.437 621-6.6-6.6 0.05 0.09 97 满足740 60 x3.5 2.437 621-6.4-6.4 0.05 0.08 97 满足741 60 x3.5 2.437 621 8.1 8.1 0.06 0.00 97 满足742 60 x3.5 2.437 621 3.5 3.5 0.03 0.00 97 满足743 60 x3.5 2.437 621-6.5-6.5 0.05 0.09 97 满足744 60 x3.5 2.437 621-1.3-1.3 0.01 0.02 97 满足745 60 x3.5 2.437 621 7.5 7.5 0.06 0.00 97 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论746 60 x3.5 2.437 621 3.5 3.5 0.03 0.00 97 满足747 60 x3.5 2.437 621-3.0-3.0 0.02 0.04 97 满足748 60 x3.5 2.437 621-4.5-4.5 0.03 0.06 97 满足749 60 x3.5 2.437 621 5.0 5.0 0.04 0.00 97 满足750 60 x3.5 2.437 621 0.6 0.6 0.00 0.00 97 满足752 60 x3.5 2.437 621-2.7-2.7 0.02 0.04 97 满足758 60 x3.5 2.012 621 3.0 3.0 0.02 0.00 80 满足762 60 x3.5 2.362 621 1.0 1.0 0.01 0.00 94 满足763 60 x3.5 2.362 621-0.8-0.8 0.01 0.01 94 满足765 60 x3.5 2.362 621 1.4 1.4 0.01 0.00 94 满足767 60 x3.5 2.362 621-0.0-0.0 0.00 0.00 94 满足768 60 x3.5 2.362 621-0.6-0.6 0.00 0.01 94 满足769 60 x3.5 2.437 621 0.1 0.1 0.00 0.00 97 满足770 60 x3.5 2.437 621 6.0 6.0 0.05 0.00 97 满足771 60 x3.5 2.437 621-1.2-1.2 0.01 0.02 97 满足772 60 x3.5 2.437 621-2.7-2.7 0.02 0.04 97 满足773 60 x3.5 2.437 621 3.4 3.4 0.03 0.00 97 满足774 60 x3.5 2.437 621 3.4 3.4 0.03 0.00 97 满足775 60 x3.5 2.437 621-2.2-2.2 0.02 0.03 97 满足776 60 x3.5 2.437 621-2.1-2.1 0.02 0.03 97 满足777 60 x3.5 2.437 621 6.2 6.2 0.05 0.00 97 满足778 60 x3.5 2.437 621 0.1 0.1 0.00 0.00 97 满足779 60 x3.5 2.437 621-2.9-2.9 0.02 0.04 97 满足780 60 x3.5 2.437 621-1.2-1.2 0.01 0.02 97 满足782 60 x3.5 2.437 621 1.9 1.9 0.01 0.00 97 满足783 60 x3.5 2.437 621-0.8-0.8 0.01 0.01 97 满足784 60 x3.5 2.437 621-0.6-0.6 0.00 0.01 97 满足788 60 x3.5 2.437 621-0.5-0.5 0.00 0.01 97 满足789 60 x3.5 2.045 621 3.2 3.2 0.02 0.00 82 满足793 60 x3.5 2.846 621 0.2 0.2 0.00 0.00 114 满足794 60 x3.5 2.012 621 0.5 0.5 0.00 0.00 80 满足795 60 x3.5 2.846 621 0.2 0.2 0.00 0.00 114 满足796 60 x3.5 2.012 621 0.5 0.5 0.00 0.00 80 满足797 60 x3.5 2.362 621 1.2 1.2 0.01 0.00 94 满足798 60 x3.5 2.362 621-0.5-0.5 0.00 0.01 94 满足799 60 x3.5 2.362 621 1.2 1.2 0.01 0.00 94 满足800 60 x3.5 2.362 621-0.5-0.5 0.00 0.01 94 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论801 60 x3.5 2.362 621 1.0 1.0 0.01 0.00 94 满足803 60 x3.5 2.362 621 1.0 1.0 0.01 0.00 94 满足805 60 x3.5 2.437 621-0.4-0.4 0.00 0.01 97 满足806 60 x3.5 2.437 621 1.5 1.5 0.01 0.00 97 满足807 60 x3.5 2.437 621-0.4-0.4 0.00 0.01 97 满足808 60 x3.5 2.437 621 1.5 1.5 0.01 0.00 97 满足809 60 x3.5 2.437 621 0.6 0.6 0.00 0.00 97 满足810 60 x3.5 2.437 621 0.6 0.6 0.00 0.00 97 满足811 60 x3.5 2.437 621 0.6 0.6 0.00 0.00 97 满足812 60 x3.5 2.437 621 0.6 0.6 0.00 0.00 97 满足813 60 x3.5 2.437 621 1.7 1.7 0.01 0.00 97 满足814 60 x3.5 2.437 621-0.5-0.5 0.00 0.01 97 满足815 60 x3.5 2.437 621 1.7 1.7 0.01 0.00 97 满足816 60 x3.5 2.437 621-0.5-0.5 0.00 0.01 97 满足817 60 x3.5 2.437 621 0.3 0.3 0.00 0.00 97 满足818 60 x3.5 2.437 621 0.8 0.8 0.01 0.00 97 满足819 60 x3.5 2.437 621 0.3 0.3 0.00 0.00 97 满足820 60 x3.5 2.437 621 0.8 0.8 0.01 0.00 97 满足822 60 x3.5 2.437 621 1.6 1.6 0.01 0.00 97 满足824 60 x3.5 2.437 621 1.6 1.6 0.01 0.00 97 满足825 60 x3.5 2.045 621 0.5 0.5 0.00 0.00 82 满足826 60 x3.5 2.846 621 0.3 0.3 0.00 0.00 114 满足827 60 x3.5 2.045 621 0.5 0.5 0.00 0.00 82 满足828 60 x3.5 2.846 621 0.3 0.3 0.00 0.00 114 满足832 60 x3.5 2.012 621 3.0 3.0 0.02 0.00 80 满足833 60 x3.5 2.362 621-0.8-0.8 0.01 0.01 94 满足836 60 x3.5 2.362 621 1.0 1.0 0.01 0.00 94 满足837 60 x3.5 2.362 621-0.0-0.0 0.00 0.00 94 满足838 60 x3.5 2.362 621-0.6-0.6 0.00 0.01 94 满足839 60 x3.5 2.362 621 1.4 1.4 0.01 0.00 94 满足841 60 x3.5 2.437 621-1.2-1.2 0.01 0.02 97 满足842 60 x3.5 2.437 621-2.7-2.7 0.02 0.04 97 满足843 60 x3.5 2.437 621 0.1 0.1 0.00 0.00 97 满足844 60 x3.5 2.437 621 6.0 6.0 0.05 0.00 97 满足845 60 x3.5 2.437 621-2.2-2.2 0.02 0.03 97 满足846 60 x3.5 2.437 621-2.1-2.1 0.02 0.03 97 满足847 60 x3.5 2.437 621 3.4 3.4 0.03 0.00 97 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论848 60 x3.5 2.437 621 3.4 3.4 0.03 0.00 97 满足849 60 x3.5 2.437 621-2.9-2.9 0.02 0.04 97 满足850 60 x3.5 2.437 621-1.2-1.2 0.01 0.02 97 满足851 60 x3.5 2.437 621 6.2 6.2 0.05 0.00 97 满足852 60 x3.5 2.437 621 0.1 0.1 0.00 0.00 97 满足853 60 x3.5 2.437 621-0.8-0.8 0.01 0.01 97 满足854 60 x3.5 2.437 621-0.6-0.6 0.00 0.01 97 满足856 60 x3.5 2.437 621 1.9 1.9 0.01 0.00 97 满足858 60 x3.5 2.437 621-0.5-0.5 0.00 0.01 97 满足863 60 x3.5 2.045 621 3.2 3.2 0.02 0.00 82 满足869 60 x3.5 2.362 621-3.5-3.5 0.03 0.04 94 满足871 60 x3.5 2.362 621 1.1 1.1 0.01 0.00 94 满足872 60 x3.5 2.362 621 5.1 5.1 0.04 0.00 94 满足873 60 x3.5 2.362 621-3.7-3.7 0.03 0.05 94 满足874 60 x3.5 2.362 621-2.4-2.4 0.02 0.03 94 满足875 60 x3.5 2.362 621 2.5 2.5 0.02 0.00 94 满足876 60 x3.5 2.362 621 6.9 6.9 0.05 0.00 94 满足877 60 x3.5 2.437 621-1.3-1.3 0.01 0.02 97 满足878 60 x3.5 2.437 621-6.2-6.2 0.05 0.08 97 满足879 60 x3.5 2.437 621 3.2 3.2 0.02 0.00 97 满足880 60 x3.5 2.437 621 8.0 8.0 0.06 0.00 97 满足881 60 x3.5 2.437 621-6.6-6.6 0.05 0.09 97 满足882 60 x3.5 2.437 621-6.4-6.4 0.05 0.08 97 满足883 60 x3.5 2.437 621 8.4 8.4 0.06 0.00 97 满足884 60 x3.5 2.437 621 8.5 8.5 0.06 0.00 97 满足885 60 x3.5 2.437 621-6.5-6.5 0.05 0.09 97 满足886 60 x3.5 2.437 621-1.3-1.3 0.01 0.02 97 满足887 60 x3.5 2.437 621 8.1 8.1 0.06 0.00 97 满足888 60 x3.5 2.437 621 3.5 3.5 0.03 0.00 97 满足889 60 x3.5 2.437 621-3.0-3.0 0.02 0.04 97 满足890 60 x3.5 2.437 621-4.5-4.5 0.03 0.06 97 满足891 60 x3.5 2.437 621 7.5 7.5 0.06 0.00 97 满足892 60 x3.5 2.437 621 3.5 3.5 0.03 0.00 97 满足894 60 x3.5 2.437 621-2.7-2.7 0.02 0.04 97 满足895 60 x3.5 2.437 621 5.0 5.0 0.04 0.00 97 满足896 60 x3.5 2.437 621 0.6 0.6 0.00 0.00 97 满足902 60 x3.5 2.004 621-2.8-2.8 0.02 0.03 80 满足单元号截面长度(m)面积(mm2)最大轴力(kN)最小轴力(kN)强度稳定长细比结论906 60 x3.5 2.355 621-3.2-3.2 0.02 0.04 94 满足909 60 x3.5 2.355 621-7.5-7.5 0.06 0.09 94 满足910 60 x3.5 2.355 621-9.2-9.2 0.07 0.12 94 满足911 60 x3.5 2.355 621 8.5 8.5 0.06 0.00 94 满足912 60 x3.5 2.355 621 10.1 10.1 0.08 0.00 94 满足913 60 x3.5 2.430 621-4.6-4.6 0.03 0.06 97 满足914 60 x3.5 2.430 621-11.2-11.2 0.08 0.15 97 满足915 60 x3.5 2.430 621 10.0 10.0 0.07 0.00 97 满足916 60 x3