外文翻译--ZLJ16摆臂式自装卸垃圾车

ZLJ16 arm type garbage truck from the loading and unloadingWith economic development, expanding cities, urban population growth, rapid increase inthe amount of municipal waste, its handling more and more attention. Municipal solid wastedisposal methods There are three forms: separation and recycling, incineration and landfill.Either approach, the final disposal sites need to be far away from urban areas. Garbage transfer vehicles on a day to play with thousands of tons of solid waste transported from the city away from the urban area ofwastedisposal plant of the taskZLJ16 arm type garbage from the transfer car is a car loading and unloading, container transport separate waste collection vehicles, mainly for medium and large municipal solid waste collection and transport, which is complete with municipal solid waste transfer equipment installed supporting the use of waste pressure products. Loose garbage installed by the pressure of compressed garbage, the volume greatly reduced, and then packing transport, can effectively improve the transfer efficiency.ZLJ arm type garbage truck from the loading and unloading from the vehicle chassis, handling systems, and trash from the three major components. 1 Chassis Steyr 1491.280/043/6x4 using two types of truck chassis, repair and exchange of good performance. The maximum total level of road quality 3.2t, the maximum speed of 85km / h. According to user needs can choose other common chassis.2 Self-priming systemSince the loading and unloading system for loading along the telescopic arm, hydraulic drive, hydraulic system pressure is 32MPa. The use of hydraulic control proportional control (cab) and direct manipulation (outside the cab) two kinds of control methods. Self-handling system installed by the subframe on the car chassis beam. Since the handling system can be reversed with a scalable two boxes L shape, and telescopic boom lift cylinders and telescopic cylinders, the rear frame above the cylinder, Vice beam with a stable, to improve the whole vehicle longitudinal stability.The car handling system from the power take-way for transmission at the end to take power.3 garbage containersZLJ16 arm type garbage truck from the loading bin is configured with the A shaped frame to enhance a special garbage container. DIN standard size using the interface. Outside the box welded trapezoidal ribs. There are two bins lower welding according to DIN standard vertical rails and durable, and compatible rear wheel bearing on both sides can achieve a smooth effortless loading and unloading bins. Trash back with automatic and manual opening and closing of the lift arm door. ZLJ16 arm type garbage truck garbage from loading and unloading containers from the loading and unloading process is as follows:Lifting garbage containers, the first manipulation of telescopic cylinders, the telescopic arm stretched out to the L shaped hook telescopic arm just below the height of the rings garbage containers, the appropriate garbage container reverse hook to hook rings. Continue to manipulate the lift cylinder, the bottom of the garbage container guide rail into the rear wheel, the rotating around the guide rollers, so that full retraction of cylinder in place lifting Post, garbage container on the frame in the horizontal position. And then manipulate the telescopic cylinder, telescopic reach out to, will forward to the tray at the bottom of the container rails on the lock block hit the frame on the locking hook up. Then manipulate the stabilizer, its piston rod fully recovered. Thus the lifting operation is complete garbage container. Remove trash containers and hoisting operation sequence in reverse order.Self-loading vehicle ZLJ arm in addition to complete self-loading garbage containers and garbage dump, but also can be carried out within a certain range of the lifting operation. In addition to the car with the unique retractable telescopic cylinder, lift cylinder, lock cylinder in order to complete the action of loading and unloading containers and garbage dump operations, but also can implement other vehicles for rescue and self-help. The car handling system can be rated in the 40s to complete the loading or loading garbage container operations in the 60s in the rubbish bin rubbish dump clean. ZLJ arm type garbage truck from the loading and unloading using an advanced hydraulic system, hydraulic control proportional control, work stable and reliable manipulation of effort, simple, micro-performance is good. ZLJ16摆臂式自装卸垃圾车随着经济的发展，城市规模不断扩大，城市人口不断快速增长，城市垃圾量急剧上升，其处理越来越受到重视。城市固体垃圾处理方法有三种形式：分类回收，焚烧和填埋。不论采用哪种处理方式，其最终处理场所均需远离城市居民区。垃圾转运车担当着将每日上千吨的固体垃圾从城市运至远离城市居民区的垃圾处理厂的重任。ZLJ16摆臂式自装卸垃圾转运车是车，箱分离式的垃圾集运车辆，主要用于大中城市固体生活垃圾的收集和运输，它是与城市固体垃圾成套转运设备的的垃圾压装机配套使用的产品。松散垃圾经垃圾压装机压缩后，体积大为减小，然后再装箱转运，可有效提高转运效率。ZLJ摆臂式自装卸垃圾车由汽车底盘，自装卸系统和垃圾箱三大部分组成。1.汽车底盘采用斯太尔1491.280/043/6x4载货汽车二类底盘，维修性和互换性能良好。其等级公路最大总质量3.2t，最高车速85km/h。根据用户需要可选用其他通用底盘。2.自装卸系统自装卸系统为顺装伸缩臂式，全液压驱动，液压系统压力为32MPa。采用液控比例操纵（驾驶室内）和直接操纵（驾驶室外）2种操纵方式。自装卸系统通过副车架安装在汽车底盘的大梁上。自装卸系统设有能够反转可伸缩的两节箱“L”形伸缩臂以及举升油缸和伸缩油缸，在车架的后上方的副梁上装有一个稳定油缸，用以提高整车的纵向稳定性。该车自装卸系统的取力方式为变速箱底取力。3.垃圾集装箱ZLJ16摆臂式自装卸垃圾车配置的垃圾箱为带“A”形提升架的专用垃圾集装箱。接口尺寸采用DIN标准。箱体外侧焊有梯形加强筋。垃圾箱下部焊装有2条符合DIN标准的纵向耐用滑轨，与车尾两侧的承重滚轮相配合，可实现垃圾箱平滑省力的装卸作业。垃圾箱后部设有可自动和手动开闭的掀臂式箱门。ZLJ16摆臂式自装卸垃圾车的垃圾集装箱的自装卸过程如下：吊装垃圾集装箱时，先操纵伸缩油缸，使伸缩臂伸出，至“L”形伸缩臂的吊钩略低于垃圾集装箱吊环的高度后，适当倒车使吊钩钩住垃圾集装箱吊环。继续操纵举升油缸，使垃圾集装箱底部导轨进入车尾部导向滚轮内，绕导向轮转动，使举升邮缸全部回缩到位，垃圾集装箱在车架上处于水平位置。再操纵伸缩油缸，使伸缩臂伸出，将集装箱向前推至托盘底部导轨上的锁块碰到车架上的锁止钩为止。然后操纵稳定器，将其活塞杆全部收回。至此垃圾集装箱的吊装作业完成。卸下垃圾集装箱的操作顺序与吊装顺序相反。ZLJ摆臂式自装卸车除了能完成垃圾集装箱的自装卸和垃圾自卸外，还可以在一定范围内进行起重作业。该车特有的伸缩臂除了配合伸缩油缸，举升油缸，锁止油缸顺序动作来完成垃圾集装箱的装卸作业和自卸作业外，还可以对其他车辆进行救援并实施自救。该车装卸系统可在40s内完成额定装载垃圾集装箱的装载或作业，可在60s内将垃圾箱内垃圾自卸干净。ZLJ摆臂式自装卸垃圾车采用了先进的液控比例操纵液压系统，工作稳定可靠，操纵省力，简便，微动性能良好。